collapse

www.dimecitycycles.com

https://www.townmoto.com/collections/vanson-leathers


www.restocycle.com

www.CITYLIMITMOTO.com

www.jadusmotorcycleparts.com

www.bisonmotorsports.com

www.speedmotoco.com

www.lostapostlejewelry.com

www.cognitomoto.com

www.sparckmoto.com

www.Moto-Madness.com

www.pistonsociety.com

www.steeltowngarage.com


Author Topic: 1974 CB360 Fallin' Ditch Hell Ride  (Read 48492 times)

Offline irk miller

  • DTT SUPPORTER
  • *
  • DTT BOTM WINNER
  • *
  • Posts: 7882
  • You've been mostly-dead all day.
Re: 1974 CB360 Fallin' Ditch Hell Ride
« Reply #450 on: Dec 19, 2017, 16:07:58 »
Here’s the situation:

Slides are 2.5 cutout
5F21 needle
O-8 Primary needle jet
130 main jet
30 slow jet

I bought a P-0 bleed style needle jet to replace the primary style.





Sent from my iPhone using DO THE TON

Offline Sonreir

  • Moderator
  • DTT SUPPORTER
  • *
  • Posts: 10776
  • Oregon
Re: 1974 CB360 Fallin' Ditch Hell Ride
« Reply #451 on: Dec 19, 2017, 16:09:34 »
What size bleed style did you end up with? In my (limited) experience, you usually have to go a lot bigger on the needle jet when you swap from primary to bleed. Often a full letter up, or more.
Sparck Moto - http://www.sparckmoto.com

Audaces fortuna iuvat.

1977 Honda CJ360 - Café SOS - Stage One™, Café SOS - Stage Two™
1976 Puch Maxi - APuchalypse Now
Suzi T500 Cobra Resto

Custom Gauge Graphics
Custom Wiring Harnesses

DTT Red, White, and/or Black 360 Club - Better than those Blue guys

Offline irk miller

  • DTT SUPPORTER
  • *
  • DTT BOTM WINNER
  • *
  • Posts: 7882
  • You've been mostly-dead all day.
Re: 1974 CB360 Fallin' Ditch Hell Ride
« Reply #452 on: Dec 19, 2017, 16:16:11 »
What size bleed style did you end up with? In my (limited) experience, you usually have to go a lot bigger on the needle jet when you swap from primary to bleed. Often a full letter up, or more.
Went from O-8 to P-0.   

Offline Sonreir

  • Moderator
  • DTT SUPPORTER
  • *
  • Posts: 10776
  • Oregon
Re: 1974 CB360 Fallin' Ditch Hell Ride
« Reply #453 on: Dec 19, 2017, 16:17:59 »
Cool. I'm interested to see how it turns out. Been meaning to go to VMs on my 378 for a while.
Sparck Moto - http://www.sparckmoto.com

Audaces fortuna iuvat.

1977 Honda CJ360 - Café SOS - Stage One™, Café SOS - Stage Two™
1976 Puch Maxi - APuchalypse Now
Suzi T500 Cobra Resto

Custom Gauge Graphics
Custom Wiring Harnesses

DTT Red, White, and/or Black 360 Club - Better than those Blue guys

Offline MiniatureNinja

  • Posts: 454
Re: 1974 CB360 Fallin' Ditch Hell Ride
« Reply #454 on: Jan 13, 2018, 00:49:17 »
this is a great build I have been following from the start, regarding the oil injection into the rocker box, does that just dump into the galley or does it intersect with the end of the camshaft where oil can move around the cam and into the galley
'75 Honda CB360 - thread

Offline irk miller

  • DTT SUPPORTER
  • *
  • DTT BOTM WINNER
  • *
  • Posts: 7882
  • You've been mostly-dead all day.
Re: 1974 CB360 Fallin' Ditch Hell Ride
« Reply #455 on: Jan 13, 2018, 02:13:52 »
this is a great build I have been following from the start, regarding the oil injection into the rocker box, does that just dump into the galley or does it intersect with the end of the camshaft where oil can move around the cam and into the galley
Thanks.  Hopefully, a little a both.  The hole lines up directly with the end of the cam shaft, but it's above the seam between the head and the cover.

Offline MiniatureNinja

  • Posts: 454
Re: 1974 CB360 Fallin' Ditch Hell Ride
« Reply #456 on: Jan 13, 2018, 12:31:00 »
Great, I've seen a lot of oil mods but yours is the most clearly photographed and seams simple enough! yours is the version I will attempt
« Last Edit: Jan 13, 2018, 12:49:41 by MiniatureNinja »
'75 Honda CB360 - thread

Offline irk miller

  • DTT SUPPORTER
  • *
  • DTT BOTM WINNER
  • *
  • Posts: 7882
  • You've been mostly-dead all day.
Re: 1974 CB360 Fallin' Ditch Hell Ride
« Reply #457 on: Jan 13, 2018, 12:58:16 »
Great, I've seen a lot of oil mods but yours is the most clearly photographed and seams simple enough! yours is the version I will attempt

It took me a minute to dig it up, as I couldn't remember if it was the 3RM CB360 or Kanticoy's Gretta.  On Gretta, Kanticoy did it similarly, but he drilled the valve cover at all the journals and used a rail to feed the oil.  He may be using a pump and reservoir, but I can't remember.  I do know he's using an external oil cooler.

http://www.dotheton.com/forum/index.php?topic=10530.1270

Offline crazypj

  • Posts: 13156
  • Split personality, I fake being smart
Re: 1974 CB360 Fallin' Ditch Hell Ride
« Reply #458 on: Jan 14, 2018, 01:13:01 »
Yep, I have full breakdown somewhere, found an electric pump that wouldn't 'kill' 360 generator but I don't remember if external reservoir was added as it would need drain back to sump. 
 Over-engineered in my opinion but I believe zero chance of cam/rocker damage plus all the extra lines, distribution points, etc. looks damn cool  8)
« Last Edit: Jan 14, 2018, 01:15:33 by crazypj »
'you can take my word for it or argue until you find out I'm right'
Best thing I ever overheard
"yep, PJ's my boss, he taught me everything I know, just didn't teach me everything he knows"
Brian Morgan, 1982

CB360's,  http://www.dotheton.com/forum/index.php?topic=11736.0
XS650,  http://www.dotheton.com/forum/index.php?topic=11922.0

Offline MiniatureNinja

  • Posts: 454
Re: 1974 CB360 Fallin' Ditch Hell Ride
« Reply #459 on: Jan 14, 2018, 01:22:19 »
I know that there are micro oil pumps out there for industrial or specialized applications, I would love to find one that wasn't much larger than the starter solenoid and do it that way
'75 Honda CB360 - thread