collapse

www.dimecitycycles.com

https://www.townmoto.com/collections/vanson-leathers


www.restocycle.com

www.CITYLIMITMOTO.com

www.jadusmotorcycleparts.com

www.bisonmotorsports.com

www.speedmotoco.com

www.lostapostlejewelry.com

www.cognitomoto.com

www.sparckmoto.com

www.Moto-Madness.com

www.pistonsociety.com

www.steeltowngarage.com

Shout Box

Pages: 1 2 3 4 [5]
  • Maritime:
  • If I was doing a job like your's. I'd just buy the HF setup
  • Aug 08, 2018, 14:29:30
  • Maritime:
  • I would just make a top and fence and put it on my portable work table, cost of a piece of MDF
  • Aug 08, 2018, 14:29:01
  • advCo:
  • I wouldn’t be able to make one for $100 plus the time
  • Aug 08, 2018, 14:26:26
  • advCo:
  • Yeah I already have a router. But I kept my rabbet bit set up on that one and used the table for slot cutter
  • Aug 08, 2018, 14:25:58
  • Maritime:
  • If I didn't already have the router that's the rout I would go LOL. but the FIL gave me a practically brand new one so I need to make or buy a table for it
  • Aug 08, 2018, 14:24:20
  • advCo:
  • I bought the HF router table. $99 for a solid table fence and router too
  • Aug 08, 2018, 14:17:33
  • Maritime:
  • Looks good, I'm doing same size for both stiles and rails 2" and will do about 1/2" slot for the panels as well. I have the router and bits but need to make a table for it
  • Aug 08, 2018, 14:10:39
  • canyoncarver:
  • Spiffy
  • Aug 08, 2018, 14:06:38
  • advCo:
  • Aug 08, 2018, 14:04:12
  • advCo:
  • 1/2" in to the rails and stiles
  • Aug 08, 2018, 13:56:39
  • advCo:
  • Nice, Yeah I did 2-1/2" stiles and 1-7/8" rails, mortise joints and cut a 3/16" slot on the inside of each piece so the ply sits 1/2
  • Aug 08, 2018, 13:56:32
  • Maritime:
  • ANd MDF has it's place but not anywhere moister can happen
  • Aug 08, 2018, 13:55:30
  • Maritime:
  • Only need to make 4 doors
  • Aug 08, 2018, 13:51:58
  • Maritime:
  • Got to get back at those
  • Aug 08, 2018, 13:51:43
  • Maritime:
  • Yep, going the exact sane route for camper doors. Solid frames and ply centers painted. Shaker style as well
  • Aug 08, 2018, 13:51:02
  • advCo:
  • I made my doors out of poplar and 1/4" ply, shaker style.
  • Aug 08, 2018, 13:39:13
  • advCo:
  • I like MDF but not for cabinets
  • Aug 08, 2018, 13:38:18
  • Maritime:
  • we do have some plywood in the shelving inside the cupboards
  • Aug 08, 2018, 13:29:13
  • Maritime:
  • It's presswood and MDF that are garbage
  • Aug 08, 2018, 13:27:59
  • Maritime:
  • Poplar is great for painted doors too
  • Aug 08, 2018, 13:27:30
  • Maritime:
  • 3/4 ply is perfectly fine for frames. Ours would be too if they weren't 30 years old.
  • Aug 08, 2018, 13:27:15
  • advCo:
  • Yeah, my cabinets are all 3/4 plywood with poplar faces. Way too expensive to build the boxes out of hardwood
  • Aug 08, 2018, 13:26:18
  • Maritime:
  • Solid wood = refinish easy. anything else is trash and replace
  • Aug 08, 2018, 13:25:44
  • Maritime:
  • Yep solid wood doors, face frames, drawer sides & bottoms and frames, no press anything or even plywood. very well made
  • Aug 08, 2018, 13:25:08
  • JustinLonghorn:
  • Which will save me some monies when it comes time to remodel.
  • Aug 08, 2018, 13:14:14
  • JustinLonghorn:
  • two of the three bathrooms have solid wood cabinets.
  • Aug 08, 2018, 13:13:56
  • advCo:
  • My countertop ended up 1/2" too high, I didnt account for the 1/2" of hardyboard that went down before the concrete. Luckily the tile we used for the backsplash had a 1/2" row at the end of each piece, so I was able to slice that to make 3 rows fit under the cabinets
  • Aug 08, 2018, 13:12:35
  • advCo:
  • Solid wood is the big thing, man. Ours were crap particleboard boxes with oak face
  • Aug 08, 2018, 13:11:12
  • Maritime:
  • We got lucky, the kitchen was solid wood custom and well designed, just counters were to low and worn out and the backsplash and knobs were horrible. so the cost of new counters, raised up and the stone backsplash with new knobs and it looks like it was built last week, even though its 30 years old
  • Aug 08, 2018, 13:07:53
Pages: 1 2 3 4 [5]