collapse

* Laugh it up fuzzball

Refresh History
  • advCo: Wipe on poly* I think i said that the other day
    Dec 14, 2018, 10:49:28
  • Maritime: That's what I think I am going to grab. couldn't find it local so I am hoping to find it tonight in Maine, got to go pick up parts and presents we ordered LOL
    Dec 14, 2018, 10:52:21
  • advCo: Nice! Minwax makes my favorite wipe on poly. 3-4 coats should be pretty good
    Dec 14, 2018, 10:54:58
  • Maritime: actually just did another search and found it, so can grab that tonight and should get the desk finished on the weekend.
    Dec 14, 2018, 10:55:06
  • advCo: Sweet
    Dec 14, 2018, 10:57:09
  • advCo: I just wipe it on lightly with a rag in small circular pattern. Hit it lightly between coats with 220
    Dec 14, 2018, 10:57:46
  • Hurco550: that desk is gonna be schweet mike
    Dec 14, 2018, 11:06:17
  • Maritime: Thanks, I have one issue, the odor level is high according to minwax. I may need to go with a low odor no VOC product because of Holly
    Dec 14, 2018, 11:15:07
  • Maritime: Varathane makes one if I can find it local
    Dec 14, 2018, 11:15:32
  • advCo: I never noticed a smell with it
    Dec 14, 2018, 11:20:13
  • advCo: The last can I got at home depot stuff stinks, not sure what brand.
    Dec 14, 2018, 11:20:45
  • irk miller: See if you can Safecoat Polyureseal, Mike. Otherwise, you can always go with a high solids oil or wax.
    Dec 14, 2018, 11:21:23
  • irk miller: *get
    Dec 14, 2018, 11:21:32
  • Maritime: Thanks, I'll look for that, there is a good little hardware store in Maine I can check out. They sell quality stuff.
    Dec 14, 2018, 11:23:01
  • Maritime: likely to have a US brand I may not find here
    Dec 14, 2018, 11:23:18
  • irk miller: [link]
    Dec 14, 2018, 11:23:22
  • Maritime: thanks I was just about to Google it
    Dec 14, 2018, 11:24:08
  • advCo: Minwax Polycrylic is a good waterbased sealer with no odor
    Dec 14, 2018, 11:26:57
  • Maritime: Cool, that I think I can get. It is actually going to be above freezing tomorrow so I could heat the garage and do it there then bring it in after it dries
    Dec 14, 2018, 11:28:13
  • advCo: I got the last piece of the rear window channel tacked in last night. Hoping to get that wrapped up this weekend and then finish the dolly and get the bus bolted to it so I can finally move it around and tip it on its side to work on the bottom
    Dec 14, 2018, 11:30:02
  • Maritime: That is available local. the minwax site has an odor warning but if you say its low I should get away with it
    Dec 14, 2018, 11:30:04
  • Maritime: Nice Nick
    Dec 14, 2018, 11:30:23
  • advCo: I found a parts bus really cheap that I'm going to try and pick up after the new year. Its over by Birmingham so a 10 hour drive but it has a perfect nose and a bunch of other parts I need
    Dec 14, 2018, 11:31:35
  • advCo: Hopefully its still available when we get back from traveling
    Dec 14, 2018, 11:32:04
  • Maritime: Hope so.
    Dec 14, 2018, 11:32:27
  • advCo: It will save me a lot in the long run. He's asking $350 for it. If i piece together the panels I need to fix the rust on the nose, and pull all the dents, that alone will cost me $350
    Dec 14, 2018, 11:36:33
  • advCo: Plus parts bus has the rear quarter that I need, extra set of doors that I'll likely use instead of mine, spare slider..etc.
    Dec 14, 2018, 11:37:13
  • Maritime: Nice, good luck, hope you get it.
    Dec 14, 2018, 11:38:31
  • Maritime: Exchange sucks for me today 37% so not likely to get anything cheaper over in ME for finishes but maybe.
    Dec 14, 2018, 11:39:24
  • advCo: Damn. Maybe I should start buying Bus parts in Canada.
    Dec 14, 2018, 11:40:33
  • Hurco550: lol rusty canadian bus parts?
    Dec 14, 2018, 11:54:44
  • advCo: Hah, no there's a couple suppliers up there for stuff like window seals, etc.
    Dec 14, 2018, 12:00:23
  • Maritime: Ha, that's funny. I am heading over tonight and picking up stuff for Jim along with mine because it's cheaper even at 37%. But some stuff goes the other way
    Dec 14, 2018, 14:31:25
  • advCo: Yeah. I need about $800 worth of seals for the bus eventually. Would save me about $200 to do it that way
    Dec 14, 2018, 15:14:05
  • Hurco550: as of one minute ago, im officially on christmas break. woot woot
    Dec 14, 2018, 16:32:10
  • advCo: Nice! I got another week -__-
    Dec 14, 2018, 16:44:00
  • Maritime: Got the desk done, crv struts swapped. Started yaris. Nearly an hour to pull one rear shock and replace. Had tonde thread the bolt and dropped a washer inside the trunk plastic liner. Fuck me, I give up for now, beer and advil fornthe sore leg hip ankle back shoulders arms and fuck Im old and fimpy
    Dec 16, 2018, 20:06:57
  • Maritime: Gimpy
    Dec 16, 2018, 20:09:07
  • advCo: Mornin' fellas
    Today at 09:54:12
  • Maritime: Morning. Off the IV pump but 4.5 months of pills. By by stomach ugg.  But need to kick the shit out of the bacteria.
    Today at 10:39:31
  • advCo: Dang man, hopefully that clears everthing up for good
    Today at 10:42:18
  • Maritime: It better LOL.  At least I get the pic out of my arm today ot tomorrow
    Today at 10:44:20
  • JustinLonghorn: Morning muchachos
    Today at 10:44:27
  • Maritime: Mornin
    Today at 10:45:34
  • JustinLonghorn: I made a sofa table over the weekend, but took no pictures.
    Today at 10:45:56
  • Maritime: Ha. I forget most of the time too
    Today at 10:46:27
  • JustinLonghorn: Wood top and sides, steel subframe.
    Today at 10:47:01
  • Maritime: Cool. Jill wants me to do somerhing like that for a coffee table now.
    Today at 10:48:03
  • Maritime: Take a pic when you get home
    Today at 11:07:44
  • advCo: Nice. I made frames for a set of coffee tables for the house like a year ago, still need to finish those
    Today at 11:32:02

* Recent Pictures - click on picture to go to post

yzf_cablemodsetup.jpg
Posted by: canyoncarver
MVIMG_20181216_161457.jpg
Posted by: imwastefull
IMG_20181216_161303.jpg
Posted by: imwastefull
IMG_2409.JPG
Posted by: irk miller
20181216_121931.jpg
Posted by: pitobread
20181216_121823.jpg
Posted by: pitobread
shock geometry.png
Posted by: jpmobius
48361295_282091485826309_3990268864184188928_n.jpg
Posted by: moubawz
48358803_354152811810541_3881439345000841216_n.jpg
Posted by: moubawz
48366088_350844978828942_4009203364947558400_n.jpg
Posted by: moubawz
48374620_1244680205657020_4797490817662976000_n.jpg
Posted by: moubawz
48367215_300213637269173_5405911259134558208_n.jpg
Posted by: moubawz
IMG_0426.JPG
Posted by: CALfeRacer
IMG_0427.JPG
Posted by: CALfeRacer
Dane Rowe back.jpg
Posted by: hidn45
IMG_0070.JPG
Posted by: Karlloss
IMG_0066.JPG
Posted by: Karlloss
IMG_0064.JPG
Posted by: Karlloss
Seat1.jpg
Posted by: Pete12
Seat.jpg
Posted by: Pete12


www.cognitomoto.com www.dimecitycycles.com

www.bisonmotorsports.com

www.jadusmotorcycleparts.com www.Moto-Madness.com

www.speedmotoco.com www.restocycle.com

www.CITYLIMITMOTO.com www.townmoto.com