collapse

www.dimecitycycles.com


www.restocycle.com

www.CITYLIMITMOTO.com

www.jadusmotorcycleparts.com

www.bisonmotorsports.com

www.speedmotoco.com

www.cognitomoto.com

www.townmoto.com

www.sparckmoto.com

www.Moto-Madness.com

www.pistonsociety.com

www.steeltowngarage.com

GET DTT UPDATES ON FACEBOOK AND TWITTER

Author Topic: Long awaited CB200 Build  (Read 14116 times)

Offline Alex jb

  • Posts: 298
Re: Long awaited CB200 Build
« Reply #110 on: Apr 10, 2018, 14:06:31 »
Nice job, is it the same output as original?
Mind if I ask what it cost ya?


Sent from my iPhone using Tapatalk

Offline bex

  • Posts: 97
Re: Long awaited CB200 Build
« Reply #111 on: Apr 10, 2018, 14:38:47 »
I havenít tested it but I think so, it was actually working before but the coatings were starting to fail so Iím not sure it would have lasted too long.

Cheap, £130 quid!

Offline MickyC

  • Posts: 1077
Re: Long awaited CB200 Build
« Reply #112 on: Apr 13, 2018, 18:42:06 »
What a awesome build. May I ask what caliper that front brembo is from. Looking to upgrade my cb200 front but am struggling to find a small one to fit.


Sent from my iPhone using DO THE TON

Offline bex

  • Posts: 97
Re: Long awaited CB200 Build
« Reply #113 on: Apr 13, 2018, 18:49:44 »
It's actually a rear caliper, as you say, nothing decent for the front fits these little bikes. I'm not even sure this setup is going to work but we'll see.

From memory its one of these: https://www.biketorqueracing.co.uk/buy/brembo-brembo-oe-rear-brake-caliper-black/20516181.htm

Offline bex

  • Posts: 97
Re: Long awaited CB200 Build
« Reply #114 on: Apr 16, 2018, 14:38:39 »
Some crankcase rebuilding pics.










Offline teazer

  • DTT SUPPORTER
  • *
  • DTT BOTM WINNER
  • *
  • Posts: 8477
Re: Long awaited CB200 Build
« Reply #115 on: Apr 16, 2018, 22:31:06 »
What size are the carbs bored to now?

Offline canyoncarver

  • DTT SUPPORTER
  • *
  • Posts: 3383
  • 'hacking is learning'
Re: Long awaited CB200 Build
« Reply #116 on: Apr 17, 2018, 23:02:50 »
What a cool build!
--
KZ400 The Rabbit
YZF750/1000R The Fly
KZ 750 Twin
ZRX 1100
65 Norton, My damn Shovelhead chop
more YZF750R's, the KZ's, a Zephyr750...and the unfinished 75' CB550 cafe.
--

Offline Alex jb

  • Posts: 298
Re: Long awaited CB200 Build
« Reply #117 on: Apr 18, 2018, 14:22:04 »
Thatís painfully clean!

Keep at it, itíll run in no time


Sent from my iPhone using Tapatalk

Offline bex

  • Posts: 97
Long awaited CB200 Build
« Reply #118 on: Apr 20, 2018, 12:00:25 »
Capellini adjustable crankcase breather



Offline Alex jb

  • Posts: 298
Re: Long awaited CB200 Build
« Reply #119 on: Apr 20, 2018, 13:35:25 »
Thatís very nice looking.

Do you need that size for venting a crank case?
I donít know, just asking