collapse

www.dimecitycycles.com


www.restocycle.com

www.CITYLIMITMOTO.com

www.jadusmotorcycleparts.com

www.bisonmotorsports.com

www.speedmotoco.com

www.cognitomoto.com

www.townmoto.com

www.sparckmoto.com

www.Moto-Madness.com

www.pistonsociety.com

www.steeltowngarage.com

QUESTIONS ABOUT THE SITE? TROUBLE REGISTERING? ADMIN@DOTHETON.COM

Author Topic: An odd one. 82 kz750r1.  (Read 5551 times)

Offline CrabsAndCylinders

  • DTT SUPPORTER
  • *
  • Posts: 1654
  • Careful With That Axe Eugene
Re: An odd one. 82 kz750r1. Brat cafe.
« Reply #60 on: Nov 18, 2017, 16:38:27 »
Love the paint on your tins!
Lighter, Quicker, Faster.
ZX-14, 900F x 2, 1100F, R100, CBR600, SR500, GT500, RZ350, KZ1000 x 2, Moto Guzzi Lemans lll, CBX550, RD 350, 750 SOHC police special, RG250, TL1000R, GT750, KTM Super Duke 1290 R, Harris/Z-1, Norton 750 Commando, Green 77 KZ650

Offline Coopacoopacoopa

  • Posts: 54
Re: An odd one. 82 kz750r1. Brat cafe.
« Reply #61 on: Nov 18, 2017, 18:20:24 »




Figured since they were off I could clean them up. Removed the casting marks, paint, and various scratches with a rolox disc. Need to pick up some bar stock as well. Can't decide whether to polish or powder coat the upper triple tree, lower triple tree, and clip on mounts.





Front calipers have seen better days. They were, at one point, a nice dark grey color. That's long gone now. Cleaned them up as best as possible. Later on I might disassemble them, refurbish them, and have them powder coated.

« Last Edit: Nov 20, 2017, 15:08:12 by Coopacoopacoopa »

Offline Coopacoopacoopa

  • Posts: 54
Re: An odd one. 82 kz750r1. Brat cafe.
« Reply #62 on: Nov 18, 2017, 18:20:58 »
Love the paint on your tins!

Thankyou!  :D

Offline Coopacoopacoopa

  • Posts: 54
Re: An odd one. 82 kz750r1. Brat cafe.
« Reply #63 on: Nov 20, 2017, 14:27:42 »
I realized I should map out my harness, so Iím in the process of drawing it up today. I am a little bit lost in translation with the factory wiring diagram. The ic igniter doesnít seem to be fused in the factory diagram? Or am I mis-reading that? Common sense tells me it should be fused. If so, what amperage fuse should I go with? 10amp or 20amp? The rectifier/regulator is direct, un-fused to the battery. Makes sense to me. Obviously the lighting system will be fused/relayed accordingly.
« Last Edit: Nov 27, 2017, 04:58:03 by Coopacoopacoopa »

Offline Coopacoopacoopa

  • Posts: 54
Re: An odd one. 82 kz750r1. Brat cafe.
« Reply #64 on: Dec 19, 2017, 15:23:04 »


Picked up some red lexan. Going to start playing with tail light design and see if I can't make something interesting and functional. 



This is where it's at right now. I know I know, rear wheel clearance. Next purchase will likely be correct length shocks and a bigger profile front tire.
« Last Edit: Dec 19, 2017, 15:24:52 by Coopacoopacoopa »

Offline Coopacoopacoopa

  • Posts: 54
Re: An odd one. 82 kz750r1. Brat cafe.
« Reply #65 on: Jan 07, 2018, 15:07:47 »


Had to replace a headlight on a customers 2007 Audi a4 due to autoleveling/high-beam actuator failure. Gotta love permanently integrated part failure. I disassembled said junk and took the projector assembly out and grafted it in. Still need to round up a clear headlight lens to finish it. I suppose I could have just purchased some ebay-special projector headlight...but what's the fun in that?  ::)

Offline MotoSquirrel

  • Posts: 19
  • Complete newbie
Re: An odd one. 82 kz750r1.
« Reply #66 on: Jan 07, 2018, 16:23:33 »
Looking quite good so far!
Jon
"So many projects, so little time. . ."
Clevelandmoto FTW!