collapse

www.dimecitycycles.com


www.restocycle.com

www.CITYLIMITMOTO.com

www.jadusmotorcycleparts.com

www.bisonmotorsports.com

www.speedmotoco.com

www.cognitomoto.com

www.townmoto.com

www.sparckmoto.com

www.Moto-Madness.com

www.pistonsociety.com

www.steeltowngarage.com

QUESTIONS ABOUT THE SITE? TROUBLE REGISTERING? ADMIN@DOTHETON.COM

Author Topic: Honda XL600R - DTRA race bike build  (Read 1256 times)

Offline Pinky23

  • Posts: 19
Honda XL600R - DTRA race bike build
« on: Sep 11, 2017, 17:07:12 »
Hey everyone! I've been wanting to build a flat tracker for a while now. Then these XL's came up on eBay.

I checked all the parts and although I'm not familiar with XL's I thought I've got pretty much everything I need to build at least one bike, maybe even 2. To be honest I won't actually be using that much of the original bike.

I've had them in my garage now for a few weeks. I'm not rushing this build. I started with the carbs, ordered full rebuild kits and set to stripping the carbs down. They where pretty manky inside. I borrowed an ultrasonic cleaner and stripped them down completely.

After reassembling the carbs I put them back on. Next I dropped the oil, put some fresh oil in, new filter, plug and plug cap. I managed to cobble together enough of a wiring loom to get a spark so I rigged up a fuel source and gave it a kick... it started on literally the first kick

Now that I know it runs I can concentrate on the chassis mods. However it was a little smokey so I might take the head off when I strip engine from the frame and re lap the valves and put some new stem seals in. Hopefully that will cure it.

Next up I managed to buy a full set of 19" wheels. Excel rims, Talon hubs and stainless spokes and they had the regulation maxxis DTR1 tyres on.


That's enough for now, but I hope to start getting a rolling chassis together this week so I'll post a few more updates then.

If anyone has any info or any sources about setting up a tracker frame geometry wise, heights etc. Please chip in!!


Sent from my iPhone using DO THE TON

Offline 1fasgsxr

  • Posts: 1152
Re: Honda XL600R - DTRA race bike build
« Reply #1 on: Sep 11, 2017, 21:53:33 »
That's a good start, following along.

Offline Pinky23

  • Posts: 19
Re: Honda XL600R - DTRA race bike build
« Reply #2 on: Sep 14, 2017, 18:49:01 »
I had some time in the garage the past few days, cleared a few jobs up with the Vmax, new forks, rebuilt fresh from the powder coaters. Rebuilt carbs. All back on and ready to get rebalanced.

My garage is a little stuffy at the moment


I had some old Vmax forks lying around so I put them in the frame because the XL forks weren't wide enough to take the new wheels with tyres.

I cleaned some spare parts up in a parts washer and then I started fitting the swingarm to the spare frame.



Once the swingarm was in the frame. I put the wheels in just to have a look at whereabouts we where. It's looking good so far though...


I can't decide whether to use the Vmax yokes, bore them out from 40 to 41 mm for the forks I want to use or go down the root of making my own yokes... I've already drawn some up, might even make some adjustable ones.

I'll keep posting updates as I go


Sent from my iPhone using DO THE TON

Offline Pinky23

  • Posts: 19
Re: Honda XL600R - DTRA race bike build
« Reply #3 on: Sep 17, 2017, 15:05:17 »
I haven't done much on the bike for the last few days but I have managed to get some adjustable triple clamps drawn up:

I also won some forks off eBay the other day from a thunder cat. I'm pretty sure they are exactly the same as the R6 5EB forks but they where only 77 delivered and the R6 ones are 250+ Happy with that. I'm hoping to get all the yokes machines asap so I can push on with the frame mods.



Sent from my iPhone using DO THE TON

Offline NoRiders

  • Posts: 626
Re: Honda XL600R - DTRA race bike build
« Reply #4 on: Sep 17, 2017, 16:56:54 »
Bloody good start fella. Looking in as I'm building a street tracker for the road :)

Carry on

Offline Pinky23

  • Posts: 19
Re: Honda XL600R - DTRA race bike build
« Reply #5 on: Sep 24, 2017, 12:59:57 »
Haven't been getting much done last week but plenty in the pipe line. I've finalised the design for the clamps and I'm just waiting on a quote back to get them ordered.

I have made a new steerer tube though, got on the lathe in work and took a couple of hours.

I turned it up out of stainless. One of my friends thinks I should have used high tensile steel but I think 24mm OD stainless should cope. Any thoughts?
Managed to get this far on my own...

Then I had to take it to a friend who's a machinist to get the thread put on. And that's it done!
I've had my forks now too so I've taken a few measurements and should be able to work out the size of the spindle, and wheel spacers I need to make so more lathe time this week hopefully.


Sent from my iPhone using DO THE TON

Offline Rat_ranger

  • Posts: 162
Re: Honda XL600R - DTRA race bike build
« Reply #6 on: Sep 24, 2017, 13:56:03 »
I made my stem out of 7075 aluminum.  Stainless should be more than strong enough
Xs650

Offline Pinky23

  • Posts: 19
Re: Honda XL600R - DTRA race bike build
« Reply #7 on: Sep 24, 2017, 15:50:27 »
Ye I'm pretty sure it will be fine. It's probably heavier than standard and definitely heavier than aluminium but it's what I was able to get hold of free


Sent from my iPhone using DO THE TON

Offline Rat_ranger

  • Posts: 162
Re: Honda XL600R - DTRA race bike build
« Reply #8 on: Sep 24, 2017, 15:59:34 »
Lol, I understand that.  Everything machined for my bike was pulled out of a scrap bin. 
Xs650

Offline Pinky23

  • Posts: 19
Re: Honda XL600R - DTRA race bike build
« Reply #9 on: Sep 25, 2017, 16:44:05 »
A small amount of progress tonight. My bearings arrived so I had a go at trial fitting the steerer tube. Pretty happy to say that it fits like a glove!

I've never done this type of swap before so I'm really happy it fits so well.
I've also had a little sketch on solidworks to see how it will look because I was a little concerned I'd made the yokes too wide.

I'm happy with the way they look so I got them ordered today and hopefully they'll be here by the end of next week.
To say I'm excited is a little bit of an understatement

I've also been looking at inspiration online and came across this...

If mine looks anything like that when it's done I'll be pretty happy


Sent from my iPhone using DO THE TON