collapse

www.dimecitycycles.com


www.restocycle.com

www.CITYLIMITMOTO.com

www.jadusmotorcycleparts.com

www.bisonmotorsports.com

www.speedmotoco.com

www.cognitomoto.com

www.townmoto.com

www.sparckmoto.com

www.Moto-Madness.com

www.pistonsociety.com

www.steeltowngarage.com

GET DTT UPDATES ON FACEBOOK AND TWITTER

Author Topic: CB450 Tracker  (Read 3438 times)

Offline 1fasgsxr

  • Posts: 1151
Re: CB450 Tracker
« Reply #10 on: Oct 24, 2017, 13:38:26 »
 :o

Offline Pete12

  • Posts: 57
Re: CB450 Tracker
« Reply #11 on: Oct 24, 2017, 18:12:48 »

Offline 1fasgsxr

  • Posts: 1151
Re: CB450 Tracker
« Reply #12 on: Oct 25, 2017, 10:14:43 »
Closest I could find to a WOW !

Offline Pete12

  • Posts: 57
Re: CB450 Tracker
« Reply #13 on: Oct 25, 2017, 18:12:03 »
Closest I could find to a WOW !

Haha, thanks.

Made some alloy front and rear engine plates and roughly bolted the bottom half of the engine in to sort out the chain alignment.
https://i.imgur.com/IEN2iFg.jpg[/img]]
https://i.imgur.com/Klp6ytj.jpg[/img]]
I had an old sprocket and chain laying around so I fitted them up. With the chain lined up and the left hand spacer in place the wheel is offset around 8mm to the right hand side so I just adjusted the spokes and pulled it over into the centre, so all good now. I don't think it will be an issue but I will pull the tyre off and make sure that there are no spoke ends poking out through the nipples.
https://i.imgur.com/QJz1mMY.jpg[/img]]
I'm having trouble sourcing a 520 16T countershaft sprocket for this motor. XL500 sprockets are very close but the spline minor diameter is 22mm as opposed to the CB450's 21mm. Not sure it would be a problem but I would like to get the correct fitting one. Anyone have any experience with this?

Offline JB56

  • Posts: 3
Re: CB450 Tracker
« Reply #14 on: Oct 26, 2017, 01:32:21 »
Thats one helluva lucky brother!!! If the intitial work is anything to go buy it will be an absolute weapon when finished....

Offline JB56

  • Posts: 3
Re: CB450 Tracker
« Reply #15 on: Oct 26, 2017, 01:36:35 »
and could you post a picture of the RD you did last year if that's OK?

Offline Pete12

  • Posts: 57
Re: CB450 Tracker
« Reply #16 on: Oct 26, 2017, 02:24:58 »
Thats one helluva lucky brother!!! If the intitial work is anything to go buy it will be an absolute weapon when finished....

Oh, don't you worry, he'll pay.. :)

Offline Pete12

  • Posts: 57
Re: CB450 Tracker
« Reply #17 on: Oct 26, 2017, 02:35:27 »
and could you post a picture of the RD you did last year if that's OK?

Thanks for your interest. Here's the RD350:
https://i.imgur.com/8barr6q.jpg[/img]]
https://i.imgur.com/2UDatGk.jpg[/img]]

Offline 1fasgsxr

  • Posts: 1151
Re: CB450 Tracker
« Reply #18 on: Oct 26, 2017, 07:59:28 »
I had my 520 sprockets made at Rebel Gears.  I don't know if you are in the states, but if so I would give them a try.

Offline Pete12

  • Posts: 57
Re: CB450 Tracker
« Reply #19 on: Oct 26, 2017, 10:02:50 »
I had my 520 sprockets made at Rebel Gears.  I don't know if you are in the states, but if so I would give them a try.

Thanks for the tip. I'm in Australia but heading to NC soon for work so I'll follow that up.