collapse

www.dimecitycycles.com


www.restocycle.com

www.CITYLIMITMOTO.com

www.jadusmotorcycleparts.com

www.bisonmotorsports.com

www.speedmotoco.com

www.cognitomoto.com

www.townmoto.com

www.sparckmoto.com

www.Moto-Madness.com

www.pistonsociety.com

www.steeltowngarage.com

GET DTT UPDATES ON FACEBOOK AND TWITTER

Author Topic: 1973 CB500 resto-mod  (Read 6060 times)

Offline scott s

  • DTT SUPPORTER
  • *
  • Posts: 1245
Re: 1973 CB500 resto-mod
« Reply #30 on: Mar 05, 2017, 17:30:40 »
 Picked up the pipes from getting them ceramic coated. "Glacier Black" on the outside and a gold/green-ish coating on the inside that's a heat dispersant.



 I also got a closer look at the pipes. They are really well made and each muffler, pipe and baffle is individually numbered.





 Here's a look at the packing on the curved baffles.



 And my guy did the hardware and hangers, too.


Offline scott s

  • DTT SUPPORTER
  • *
  • Posts: 1245
Re: 1973 CB500 resto-mod
« Reply #31 on: Mar 05, 2017, 17:33:47 »
The pistons were vapor blasted, then coated with "Piston Coat" on the tops and "Micro Slick" on the skirts. Heat reflective and thin film lubricant, respectively.




Offline The Limey

  • Posts: 198
  • Load Bearing Member
Re: 1973 CB500 resto-mod
« Reply #32 on: Mar 08, 2017, 03:59:37 »
Sexy. My Y fronts also became coated with something looking at that  :-*
If it ain't broke, then I haven't been hitting it hard enough.

Offline scott s

  • DTT SUPPORTER
  • *
  • Posts: 1245
Re: 1973 CB500 resto-mod
« Reply #33 on: Mar 11, 2017, 20:37:35 »
 I said I wasn't gonna do this, but I couldn't stand it. Everything else is getting powdercoated, painted, polished, chromed or detailed. The front was actually OK, but the rear was a little faded and chipped. They looked good from five feet away, but not so much up close.
 The lips got a hand polish to a shiny satin sheen, the body got a satin black paint job.
 Oh....and I also sanded down the fork lowers and painted them silver, followed with clear coat. They also got rebuilt with new seals, oil and a full service.


Offline scott s

  • DTT SUPPORTER
  • *
  • Posts: 1245
Re: 1973 CB500 resto-mod
« Reply #34 on: Mar 11, 2017, 22:24:49 »
 Mo' better.


Offline scott s

  • DTT SUPPORTER
  • *
  • Posts: 1245
Re: 1973 CB500 resto-mod
« Reply #35 on: Mar 13, 2017, 17:31:56 »
 Got the top end mostly done today. Now I can move on to timing the cam, as well as a few other odds and ends, like flipping the engine over to pull the sump, clean and inspect and replace the gasket. I can also start installing the new clutch discs, side covers, etc.




Offline tattoo

  • Posts: 113
Re: 1973 CB500 resto-mod
« Reply #36 on: Mar 13, 2017, 20:17:13 »
nice!!!

attention to details so far is inspiring.

subscribed


Offline irk miller

  • DTT SUPPORTER
  • *
  • DTT BOTM WINNER
  • *
  • Posts: 6531
  • You've been mostly-dead all day.
Re: 1973 CB500 resto-mod
« Reply #37 on: Mar 13, 2017, 20:31:17 »
You plan on doing the spin-on oil filter conversion, scott?  I love the kit Randakk puts out for them. 

Offline scott s

  • DTT SUPPORTER
  • *
  • Posts: 1245
Re: 1973 CB500 resto-mod
« Reply #38 on: Mar 13, 2017, 20:46:14 »
 I hadn't, but I might have to look into it now. I have a Nighthawk oil cooler that may go on it at a later date.