Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature currently requires accessing the site using the built-in Safari browser.
We noticed you are blocking ads. DO THE TON only works with community supporters. Most are active members of the site with small businesses. Please consider disabling your ad blocking tool and checking out the businesses that help keep our site up and free.
Since I got my XS750 working properly-ish,I would like to refresh the existing paint scheme.
First I thought just polishing the existing clear would do,but then I saw how low the coverage on the decals are so I guess I need to lay on a few layers of 2K clear.
How would you guys go about cleaning and prepping the tank,especially around the fuel opening on top there is bad grime....
Try a degreaser with a toothbrush to get in the nooks and crannies of the tank. Also some solvents such as acetone are very good at removing that type of gunk and should not harm the existing finish (try in an inconspicuous location, first).
I´ll probably try a brass brush dremel piece on really low speed on the hard to get to spots around the tank bung and some scotch brite with acetone (gonna try on an unsuspiciois spot first!).
The tank has slight surface rust spots, maybe I will make a slight derust on it.Normally I use phosporc acid which seems to be excess on that type of rust.
How would you guys go about derusting the inside without destroying the stock paint?
Found this in my wisdom word document:
Mobius : "Minor rust in a tank is crazy over rated. If it is so bad it gets loose, it is easy to mechanically scrub away. I do not use any sort of fuel filters past the screens in most petcocks (unless there aren't any) and have never had an issue. (45 years of riding in widely various territories - daily for much of that time). Bad gas is another story, but the screens in most oem petcock will be all you need in my experience. My money says if your tank is generally sound, the above abrasive scrub with gravel will END any further issues."
In my experience, varnish that peels is a way higher concern than interior flash rust. If your tank is clean (free of varnish/old gas) you can try the old chain shake with phosphoric acid. Or even better, and correspondingly more expensive, do the old evapo-rust treatment. That won't harm the exterior finish, and may even be safe enough to spot treat those areas by the filler cap. You could even try the electrolysis method, but when I did it left a plating of soda ash in the bottom of my tank. Pretty annoying.
I would like to try the chain method.
Phosporic is pretty harsh on the paint,which I'm trying to preserve.
Since I'm based in Austria,we have no evaporust :-(
Any alternatives like citric acid?
I could try electrolysis,but IIRC its not that effective....
regular white vinegar will do it, it just takes a little longer. Fill the tank to the top, let it sit 3-4 days then pour out the vinegar and rinse it well with baking soda and water to neutralize the acid. Then dry with a hair dryer and fill with gas or spray a little wd-40 in to prevent rust until you can put gas in.
regular white vinegar will do it, it just takes a little longer. Fill the tank to the top, let it sit 3-4 days then pour out the vinegar and rinse it well with baking soda and water to neutralize the acid. Then dry with a hair dryer and fill with gas or spray a little wd-40 in to prevent rust until you can put gas in.
Not sure, I just go buy the 4L jugs at the grocery store. I can check the label on the jug I have at home tonight and see if it says the concentration on it.
Not sure, I just go buy the 4L jugs at the grocery store. I can check the label on the jug I have at home tonight and see if it says the concentration on it.
Just got the fresh petcocks from MikeXS and probably gonna sand the tank with 1000grit then respray with 2K clear...in between I would like to use the vinegar!
So guys...the XS is finally MOT'd and now I can spend time on the paint.
How would you guys treat paint chips on the tank?
There are a few spots were rust spots are showing...
Should I just leave them alone and 2K over them or sand and respray?
So guys...the XS is finally MOT'd and now I can spend time on the paint.
How would you guys treat paint chips on the tank?
There are a few spots were rust spots are showing...
Should I just leave them alone and 2K over them or sand and respray?
Unless you know exactly what kind of clear is already on there you run a risk of having compatibility issues. If it was me I'd do a light color sand, buff it, and call it a day.
Unless you know exactly what kind of clear is already on there you run a risk of having compatibility issues. If it was me I'd do a light color sand, buff it, and call it a day.
Never had any issues combining 2K paint with any other paint,the only issue i´m having right now is that there are minor rust points on the outside of the tank and clearing over them could be an issue..
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.