* Laugh it up fuzzball

Refresh History
  • Hurco550: i know 15km doesnt sound like much, but its a good long shot on the old iron haha
    Feb 16, 2018, 14:45:54
  • Maritime: Ha yep, there should still be lots of snow as it's dipping to 2 deg overnight tonight and most of the day sat, not going up until sun afternoon
    Feb 16, 2018, 17:01:34
  • Hurco550: as long as it doenst end up that warm on the day of the ride we sould be good then. Last trip like that i went on we set out in the morning and it was around 20f. on the way back the temp shot up to around 40f, and resulted in the old wheelhorse snowmobile i was on melting a hole through the piston. They dont like warm weather
    Feb 16, 2018, 17:09:04
  • Jewbacca: Afternoon folks
    Feb 17, 2018, 16:23:42
  • Hurco550: Happy Monday y'all
    Feb 19, 2018, 09:53:32
  • SONIC.: Eh, if you say so
    Feb 19, 2018, 10:16:35
  • Hurco550: I'm off work today, so I do say so lol
    Feb 19, 2018, 10:32:56
  • Maritime: Ha, fmaily day here but I got to work because we are federally regulated companuy and the holiday is provician'
    Feb 19, 2018, 10:46:54
  • Maritime: Provincial
    Feb 19, 2018, 10:47:00
  • Maritime: How'd the sled trip got Levi or is that next weekend?
    Feb 19, 2018, 10:47:17
  • The Jimbonaut: Top of the morning question time, torquing head bolts - Clymers says 48ft lbs but my Canadian Tire wrench starts at 50.  Think 50ft lbs will be ok, given that apparently these things can be a little inaccurate anyway?
    Feb 19, 2018, 10:51:20
  • SONIC.: As long as it's inaccurate on the low side :D
    Feb 19, 2018, 10:56:10
  • Maritime: They are usually rated at +/- 4%, 2% etc. If it's 50 lbs +/- 4% it 48-52 ft lbs, not sure that will snap a bolt or not
    Feb 19, 2018, 11:09:01
  • Maritime: if you set it a little below the 50 ft lb line you should be safe
    Feb 19, 2018, 11:09:29
  • The Jimbonaut: ^^ I tried that yesterday Mike - set it a little below the 50 ft lb mark but when I didn't hear a click I got the fear and thought maybe torque wrenches don't like being backed off below their minimum setting
    Feb 19, 2018, 11:11:18
  • The Jimbonaut: Think if I back it off 2 ft lbs from the 50 ft lb mark I should be ok?
    Feb 19, 2018, 11:12:03
  • SONIC.: It should still work, 50 ftlbs is way tighter than you think, I'm always thinking "this bitch is going to snap" all the way up to the click
    Feb 19, 2018, 11:12:48
  • paddyshepherd: I would imagine you'd be fine - there will be a FoS on the torque settings anyway so I can't imagine there being an issue.
    Feb 19, 2018, 11:12:50
  • The Jimbonaut: No kidding - it was sweaty palm time while I was cranking on that thing and decided to back off until I'd consulted with you guys
    Feb 19, 2018, 11:14:57
  • The Jimbonaut: By the way, what's an FoS?
    Feb 19, 2018, 11:15:30
  • Maritime: the only issue I can see is if you need to build the torque up. When I do the Yamaha heads I need to start at like 20 and then 30 and then the final 40 so there is like 6 nuts to do in sequence like that
    Feb 19, 2018, 11:16:02
  • The Jimbonaut: Yeah man, in sequence and building the torque up incrementally
    Feb 19, 2018, 11:17:17
  • Maritime: can't do that right if 48 is the final spec, fine if 48 is the start and you end at like 60 something, it all depends on the spec.  My GL heads are like 60ish ft lbs but the air cooled yamaha tops at 40 so I need the smaller wrench for those
    Feb 19, 2018, 11:19:13
  • paddyshepherd: FoS means Factor of Safety :)
    Feb 19, 2018, 11:20:15
  • Maritime: Jim if you want to wait, Jill's going over to Houlton today and could grab you this: [link]
    Feb 19, 2018, 11:21:43
  • Maritime: probably only cost 5 bucks to send it on the bus.
    Feb 19, 2018, 11:22:03
  • Maritime: That's 30 CAD vs CT price not on sale of well over 100
    Feb 19, 2018, 11:23:14
  • The Jimbonaut: pm'd you Mike
    Feb 19, 2018, 11:56:05
  • The Jimbonaut: Factor of Safety, gotcha
    Feb 19, 2018, 12:09:11
  • canyoncarver: Hubba Hubba: 
    Feb 19, 2018, 14:42:52
  • The Jimbonaut: Mmmmmm, this is about 45 mins north of me [link]
    Feb 20, 2018, 10:47:31
  • The Jimbonaut: Damn - that link was to a '72 CT70.  Look like it sold in less than an hour
    Feb 20, 2018, 12:12:49
  • The Jimbonaut:
    Feb 20, 2018, 12:25:47
  • The Jimbonaut: La Impetuosa.  Crikey.
    Feb 20, 2018, 12:51:04
  • advCo: Dang, that thing is mean looking
    Feb 20, 2018, 12:58:06
  • advCo: Hey Jim, turns out I ended up needing that kickstarter shaft I linked you for the Van Van. I started it up the other day just to find out that the kicker only works about 10% ofthe time
    Feb 20, 2018, 13:27:51
  • canyoncarver: That is a beautiful Diavel makeover.
    Feb 20, 2018, 13:38:21
  • The Jimbonaut: No kidding Nick - did you find one?  I can ask my guy here if he has one knocking about if you have a hard time sourcing one
    Feb 20, 2018, 13:39:41
  • The Jimbonaut: Yeah that Diavel is something else
    Feb 20, 2018, 13:41:11
  • advCo: Yeah - I ended up buying that one I linked ya the other day
    Feb 20, 2018, 13:43:06
  • The Jimbonaut: Ah, the irony
    Feb 20, 2018, 13:45:46
  • advCo: Yep, so I'll be splitting the cases again soon
    Feb 20, 2018, 13:46:09
  • The Jimbonaut: Oh the joys...
    Feb 20, 2018, 13:46:22
  • advCo: Should be a weekend job, just have to clear enough space on the bench so I don't lose all the bits
    Feb 20, 2018, 13:50:15
  • advCo: Other than that and the petcock pissing a gallon of fuel all over the walkway, it should be about finished
    Feb 20, 2018, 13:50:35
  • advCo: On the plus side, I learned that the Rustoleum appliance epoxy is fuel resistant.
    Feb 20, 2018, 13:54:09
  • The Jimbonaut: Know all about leaky petcocks - the KLR had a concerning incontinence issue when I picked it up.  Post up some pics mate - now the Van Van is as good as done bet that Ghia is fixing for a wrench...
    Feb 20, 2018, 14:03:02
  • canyoncarver: :)  [link]
    Feb 20, 2018, 15:49:24
  • advCo: mhmmm
    Feb 20, 2018, 16:06:31
  • advCo: Yep I hope to get the floors in the Ghia this weekend
    Feb 20, 2018, 16:06:40

* Recent Pictures - click on picture to go to post

Posted by: stroker crazy
Posted by: stroker crazy
Posted by: Wangofree
Posted by: Sonreir
Posted by: cb250nproject
Posted by: cb250nproject
Posted by: beachcomber
Picture 068.jpg
Posted by: beachcomber
Picture 058.jpg
Posted by: beachcomber
Picture 068.jpg
Posted by: beachcomber
Picture 058.jpg
Posted by: beachcomber
Posted by: cb250nproject
Posted by: cb250nproject
Posted by: stroker crazy
Posted by: stroker crazy
Posted by: Bevelheadmhr
Posted by: Bevelheadmhr
Posted by: beachcomber
Posted by: beachcomber
IMG_1506 (1).JPG
Posted by: beachcomber

* #DOTHETON Instagram