** PICS OF MEMBERS RIDES ** - Official Before & After Thread

Before and not quite after.
 

Attachments

  • cv 010.JPG
    cv 010.JPG
    1.5 MB · Views: 248
  • ytg 001.JPG
    ytg 001.JPG
    1.7 MB · Views: 257
All but the badges and fine tuning.
 

Attachments

  • ImageUploadedByTapatalk1370956636.834714.jpg
    ImageUploadedByTapatalk1370956636.834714.jpg
    275.6 KB · Views: 246
  • ImageUploadedByTapatalk1370956597.902025.jpg
    ImageUploadedByTapatalk1370956597.902025.jpg
    359.1 KB · Views: 240
  • ImageUploadedByTapatalk1370956583.582934.jpg
    ImageUploadedByTapatalk1370956583.582934.jpg
    92.2 KB · Views: 1,424
  • ImageUploadedByTapatalk1370956556.267152.jpg
    ImageUploadedByTapatalk1370956556.267152.jpg
    119.9 KB · Views: 1,470
she's changed forms a few times now... 1970 Honda CL450
 

Attachments

  • photo[9].JPG
    photo[9].JPG
    408.3 KB · Views: 264
  • IMG_3571.jpg
    IMG_3571.jpg
    158.9 KB · Views: 1,595
  • IMG_3087.PNG
    IMG_3087.PNG
    1.2 MB · Views: 259
  • IMG_3085.PNG
    IMG_3085.PNG
    1.1 MB · Views: 245
canyoncarver said:
Nice bike. Do you have more pics and info on the intake setup you did?

As soon as she is badged up ill take a heap if pics and post them up.

Intake is pretty stock. Stock carbs with new jets. I used a uni filter on the intake as the old box filters had perished. I still have a bit of tuning to do as she could run a little richer.
Check out the build thread bellow if you want a few more pics too I think there's one of the intake on there.
 
Heres me new build..

Before

c530.jpg


After
zesx.jpg


Specs:
Rebuild motor, 1st overbore, new rings, gaskets, seals, valve seals, etc etc
PMA Swap with RD Rotor, and GSXR reg/rec
Pamco High output ignition with green monster coil
Triumph Capacitor
Minimal wiring all wrapped in braided sleeving, to a new mini fuse block under the seat
RD400 front end with air valves
Super wide #10 bend bars
4.5" Light
Mini throttle housing
KTM dirtbike brake master
Bronze bushings
12.5" gas charged rear shocks
Drilled and Rebuilt drum
Skate wheel tail light
SHorty fender
Handmade seat

Every nut and bolt was replaced with new, all the aluminum polished, etc etc.

Bangin!
 
tron97 said:
Heres me new build..

Before

c530.jpg


After
zesx.jpg


Specs:
Rebuild motor, 1st overbore, new rings, gaskets, seals, valve seals, etc etc
PMA Swap with RD Rotor, and GSXR reg/rec
Pamco High output ignition with green monster coil
Triumph Capacitor
Minimal wiring all wrapped in braided sleeving, to a new mini fuse block under the seat
RD400 front end with air valves
Super wide #10 bend bars
4.5" Light
Mini throttle housing
KTM dirtbike brake master
Bronze bushings
12.5" gas charged rear shocks
Drilled and Rebuilt drum
Skate wheel tail light
SHorty fender
Handmade seat

Every nut and bolt was replaced with new, all the aluminum polished, etc etc.

Bangin!

Hey tron! Do you have a picture of that "Skate wheel tail light"
It sounds sweeeeeet!
 
79 KZ1000ST Before and After
 

Attachments

  • kz1000st.jpg
    kz1000st.jpg
    253.3 KB · Views: 486
  • NewBike1.jpg
    NewBike1.jpg
    1.8 MB · Views: 353
  • NewBike2.jpg
    NewBike2.jpg
    306.9 KB · Views: 259
my '78 GS550E
 

Attachments

  • DSCF1025 lo.jpg
    DSCF1025 lo.jpg
    640.4 KB · Views: 256
  • handlebars-cowl 02lo.jpg
    handlebars-cowl 02lo.jpg
    719.3 KB · Views: 239
  • Before.JPG
    Before.JPG
    129.3 KB · Views: 249
  • DSCF1011 70s.jpg
    DSCF1011 70s.jpg
    828.5 KB · Views: 253
My Yamaha SR250 - just finished
 

Attachments

  • DSCF0979 (1024x768).jpg
    DSCF0979 (1024x768).jpg
    656.5 KB · Views: 242
  • 20130630_155929 (1024x807).jpg
    20130630_155929 (1024x807).jpg
    708.8 KB · Views: 278
  • 20130630_172428 (1024x768).jpg
    20130630_172428 (1024x768).jpg
    674.1 KB · Views: 231
  • 20130630_172447 (1024x768).jpg
    20130630_172447 (1024x768).jpg
    693.9 KB · Views: 264
Back
Top Bottom