collapse

www.cognitomoto.com

www.dimecitycycles.com

https://www.townmoto.com/collections/vanson-leathers


www.restocycle.com

www.CITYLIMITMOTO.com

www.jadusmotorcycleparts.com

www.bisonmotorsports.com

www.speedmotoco.com

www.lostapostlejewelry.com

www.sparckmoto.com

www.pistonsociety.com

www.steeltowngarage.com


Author Topic: CB360 Carb swap and sync  (Read 11158 times)

Offline MiniatureNinja

  • Posts: 490
Re: CB360 Carb swap and sync
« Reply #10 on: Apr 26, 2018, 18:16:22 »
'Bumping' this to top since I saw someone is looking for it

thanks, I wasn't looking but I'm glad I came accross it!
'75 Honda CB360 - thread

Offline crazypj

  • Posts: 13223
  • Split personality, I fake being smart
Re: CB360 Carb swap and sync
« Reply #11 on: Apr 28, 2018, 23:43:11 »
It's amazing the stuff you find when not looking, I know I've wasted hours watching Russian 'driver' video's  ;D
'you can take my word for it or argue until you find out I'm right'
Best thing I ever overheard
"yep, PJ's my boss, he taught me everything I know, just didn't teach me everything he knows"
Brian Morgan, 1982

CB360's,  http://www.dotheton.com/forum/index.php?topic=11736.0
XS650,  http://www.dotheton.com/forum/index.php?topic=11922.0

Offline crazypj

  • Posts: 13223
  • Split personality, I fake being smart
Re: CB360 Carb swap and sync
« Reply #12 on: May 02, 2018, 07:48:44 »
Because of truck issues, I've been looking up Lambda sensors. (O2 sensor)
Even though it doesn't apply to stock 360s (or modified ones really) this is the best video I've ever seen explaining how they work and what they do. It will be of interest to anyone fitting one to older bike. Gives some good information , particularly about NOT using dielectric grease in connectors (lot of bad advice out there about stuff like that)


BTW,. you only need to watch about first 30 mins, the rest is on actual vehicles so pretty worthless to 'us'
« Last Edit: May 02, 2018, 09:48:29 by crazypj »
'you can take my word for it or argue until you find out I'm right'
Best thing I ever overheard
"yep, PJ's my boss, he taught me everything I know, just didn't teach me everything he knows"
Brian Morgan, 1982

CB360's,  http://www.dotheton.com/forum/index.php?topic=11736.0
XS650,  http://www.dotheton.com/forum/index.php?topic=11922.0

Offline CrabsAndCylinders

  • DTT SUPPORTER
  • *
  • Posts: 1995
  • Careful With That Axe Eugene
Re: CB360 Carb swap and sync
« Reply #13 on: May 03, 2018, 22:45:04 »
It's amazing the stuff you find when not looking, I know I've wasted hours watching Russian 'driver' video's  ;D

Those vids give me the chills!
Lighter, Quicker, Faster.
ZX-14, 900F x 2, 1100F, R100, CBR600, SR500, GT500, RZ350, KZ1000 x 2, Moto Guzzi Lemans lll, CBX550, RD 350, 750 SOHC police special, RG250, TL1000R, GT750, KTM Super Duke 1290 R, Harris/Z-1, Norton 750 Commando, Green 77 KZ650

Offline crazypj

  • Posts: 13223
  • Split personality, I fake being smart
Re: CB360 Carb swap and sync
« Reply #14 on: May 12, 2018, 16:05:34 »
After watching the Common Motor Collective video where Brenden uses sealer on carb vacuum chambers I thought I should add this as correct way to make sure you don't have air leaks. DO NOT USE SEALER ON CARBS
Just a few pictures with some explanations .1. Things you need. Carb, Sharpie, flat surface (using a marble floor tile, not everyone has a surface plate) and 220 grit 'WetorDry' 2. Use marker around outside top edge of carb body.. 3.Rub top on wetordry ,shadow still visible between screws.  4.Check surface is flat,pointer doesn't show it too well but just below it is still 'shadow', very common to find as much as 0.030" distortion. 5. when it's all smooth and flat your done. Note - Do the steel tops first as it cut down the 'bite' of sandpaper, they always need doing. If you need a flat surface, anywhere that does marble or granite counter tops should have several pieces where they remove area for sink. It is more than accurate enough for this
« Last Edit: May 13, 2018, 13:34:00 by crazypj »
'you can take my word for it or argue until you find out I'm right'
Best thing I ever overheard
"yep, PJ's my boss, he taught me everything I know, just didn't teach me everything he knows"
Brian Morgan, 1982

CB360's,  http://www.dotheton.com/forum/index.php?topic=11736.0
XS650,  http://www.dotheton.com/forum/index.php?topic=11922.0

Offline trek97

  • DTT SUPPORTER
  • *
  • DTT BOTM WINNER
  • *
  • Posts: 6093
Re: CB360 Carb swap and sync
« Reply #15 on: May 12, 2018, 23:04:27 »
+1.  Nicely done.

Offline crazypj

  • Posts: 13223
  • Split personality, I fake being smart
Re: CB360 Carb swap and sync
« Reply #16 on: May 13, 2018, 13:36:28 »
I was going to add link into video replies but gaven't been on You Tube yet
'you can take my word for it or argue until you find out I'm right'
Best thing I ever overheard
"yep, PJ's my boss, he taught me everything I know, just didn't teach me everything he knows"
Brian Morgan, 1982

CB360's,  http://www.dotheton.com/forum/index.php?topic=11736.0
XS650,  http://www.dotheton.com/forum/index.php?topic=11922.0

Offline CrabsAndCylinders

  • DTT SUPPORTER
  • *
  • Posts: 1995
  • Careful With That Axe Eugene
Re: CB360 Carb swap and sync
« Reply #17 on: May 13, 2018, 18:01:57 »
After watching the Common Motor Collective video where Brenden uses sealer on carb vacuum chambers I thought I should add this as correct way to make sure you don't have air leaks. DO NOT USE SEALER ON CARBS
Just a few pictures with some explanations .1. Things you need. Carb, Sharpie, flat surface (using a marble floor tile, not everyone has a surface plate) and 220 grit 'WetorDry' 2. Use marker around outside top edge of carb body.. 3.Rub top on wetordry ,shadow still visible between screws.  4.Check surface is flat,pointer doesn't show it too well but just below it is still 'shadow', very common to find as much as 0.030" distortion. 5. when it's all smooth and flat your done. Note - Do the steel tops first as it cut down the 'bite' of sandpaper, they always need doing. If you need a flat surface, anywhere that does marble or granite counter tops should have several pieces where they remove area for sink. It is more than accurate enough for this

Thanks, good idea.
Lighter, Quicker, Faster.
ZX-14, 900F x 2, 1100F, R100, CBR600, SR500, GT500, RZ350, KZ1000 x 2, Moto Guzzi Lemans lll, CBX550, RD 350, 750 SOHC police special, RG250, TL1000R, GT750, KTM Super Duke 1290 R, Harris/Z-1, Norton 750 Commando, Green 77 KZ650

Offline crazypj

  • Posts: 13223
  • Split personality, I fake being smart
Re: CB360 Carb swap and sync
« Reply #18 on: Jul 31, 2018, 20:16:36 »
I thought I had picture of correct angle to setfloat level but apparently not here. Just took a pic for a different thread but it's just right for this as well. This is set I just got to work on, will be cleaned and modified then re-set to 21mm for CB360

'you can take my word for it or argue until you find out I'm right'
Best thing I ever overheard
"yep, PJ's my boss, he taught me everything I know, just didn't teach me everything he knows"
Brian Morgan, 1982

CB360's,  http://www.dotheton.com/forum/index.php?topic=11736.0
XS650,  http://www.dotheton.com/forum/index.php?topic=11922.0