collapse

www.dimecitycycles.com

www.cognitomoto.com

https://www.townmoto.com/collections/vanson-leathers

www.speedmotoco.com

www.CITYLIMITMOTO.com

www.jadusmotorcycleparts.com

www.lostapostlejewelry.com

www.sparckmoto.com

www.pistonsociety.com


Author Topic: CB350 Lucy Project Complete  (Read 7080 times)


Offline JustinLonghorn

  • DTT SUPPORTER
  • *
  • Posts: 6677
  • No Purple Hearts, No Blue Ribbons
Re: CB350 Lucy Project Complete
« Reply #1 on: Nov 28, 2011, 10:45:31 »
yep, I can dig it.
I'm going to eat your brains and gain your knowledge.

Into The Sunset, CB750 build

TT500 the Animal

Offline jonnyTHUNDERmaker

  • Posts: 609
Re: CB350 Lucy Project Complete
« Reply #2 on: Nov 28, 2011, 10:47:35 »
VERY NICE!!!! Great work, that is a really good looking bike. I love the headlight fin. Is it just me or is the seat cowl, or the pinstripes on the seat cowl a tad askew?

Offline m511y

  • Posts: 442
  • Less is more
Re: CB350 Lucy Project Complete
« Reply #3 on: Nov 28, 2011, 10:50:12 »
VERY NICE!!!! Great work, that is a really good looking bike. I love the headlight fin. Is it just me or is the seat cowl, or the pinstripes on the seat cowl a tad askew?

I think the angle of the shot and the offset of the rear wheel make it look a little off, but it isn't.

Offline ProSimex

  • DTT SUPPORTER
  • *
  • Posts: 1036
  • RUN SCREAMING!!!
Re: CB350 Lucy Project Complete
« Reply #4 on: Nov 28, 2011, 12:30:58 »
Very nice, very clean.  That hot little unit could use a fork brace though ;)
"Love is the feelin you get when you like something as much as your motorcycle."

"That's got CV's? Take a #2 phillips screwdriver, heat the tip with a torch until cherry red and plunge it into your eye. It will hurt less. Really."- Kopcicle

Offline m511y

  • Posts: 442
  • Less is more
Re: CB350 Lucy Project Complete
« Reply #5 on: Dec 02, 2011, 17:03:44 »
Very nice, very clean.  That hot little unit could use a fork brace though ;)

I haven't ever seen one other than the front fender. I like the look better with out it as long as it isn't a safty hazzard. I think the front end handles just fine without one. I was thinking about fabricating one from the stock fender mount, but I'm not a fan of how it looks. Is it likley the forks will fail without one?

Offline bravecafe

  • Posts: 111
  • "Putting the Duh in Honda since 1962 !"
Re: CB350 Lucy Project Complete
« Reply #6 on: Dec 02, 2011, 17:22:39 »
Very NICE !
Got me motivated to get my butt back in the shop in and finish the insulation and lights so I can finish my 350 .
1966 CB771968 T5001969 CL 350 (x4) 1971 CB 450 1972 cb750 1973 cb750 1973 cb1751974 cb350f (x2) 1974 cf400f 1980 GN 400 1981 CX 500


Offline m511y

  • Posts: 442
  • Less is more
Re: CB350 Lucy Project Complete
« Reply #8 on: Dec 02, 2011, 23:37:14 »
Very NICE !
Got me motivated to get my butt back in the shop in and finish the insulation and lights so I can finish my 350 .

Post a pic of your CB on here.

Offline bravecafe

  • Posts: 111
  • "Putting the Duh in Honda since 1962 !"
CB350 Lucy Project Complete
« Reply #9 on: Dec 03, 2011, 02:22:23 »
I'll post a build thread as soon as I get outta shop construction mode.
Anyone know if I should use clip ons or clubmans on my ladder to sheetrock the ceiling? Lol going for r-90 in the attic too :)
1966 CB771968 T5001969 CL 350 (x4) 1971 CB 450 1972 cb750 1973 cb750 1973 cb1751974 cb350f (x2) 1974 cf400f 1980 GN 400 1981 CX 500