collapse

www.dimecitycycles.com

www.cognitomoto.com

https://www.townmoto.com/collections/vanson-leathers

www.speedmotoco.com

www.CITYLIMITMOTO.com

www.jadusmotorcycleparts.com

www.lostapostlejewelry.com

www.sparckmoto.com

www.pistonsociety.com


Author Topic: 1974 CB360 Fallin' Ditch Hell Ride  (Read 62923 times)


Offline advCo

  • DTT BOTM WINNER
  • *
  • Posts: 3229
  • Nick Ol' Eye
    • adventur Studios
Re: 1974 CB360 Fallin' Ditch Hell Ride
« Reply #191 on: Oct 04, 2016, 01:25:47 »
So you're increasing the total volume of oil within the motor, opened up the stock passages, and have oil flowing to the top end through the external tank -does that result in lower pressure through the filter/galley and external reservoir?

If the pressure is now essentially split between the two channels, will there be enough pressure to get oil up top through either route?


Sent from my iPhone using DO THE TON

Offline irk miller

  • DTT SUPPORTER
  • *
  • DTT BOTM WINNER
  • *
  • Posts: 9129
  • You've been mostly-dead all day.
Re: 1974 CB360 Fallin' Ditch Hell Ride
« Reply #192 on: Oct 04, 2016, 01:42:12 »
Yes no. You tell me. Please provide the math. I rely on trial and error.


Sent from my iPhone using DO THE TON

Offline advCo

  • DTT BOTM WINNER
  • *
  • Posts: 3229
  • Nick Ol' Eye
    • adventur Studios
Re: 1974 CB360 Fallin' Ditch Hell Ride
« Reply #193 on: Oct 04, 2016, 01:56:04 »
All in theory. I'm just spitballing here.

Offline irk miller

  • DTT SUPPORTER
  • *
  • DTT BOTM WINNER
  • *
  • Posts: 9129
  • You've been mostly-dead all day.
Re: 1974 CB360 Fallin' Ditch Hell Ride
« Reply #194 on: Oct 04, 2016, 02:25:30 »
All in theory. I'm just spitballing here.
In theory, it should be create better functional flow.  The pump's pressure is the same.  I haven't changed the motor's oil pump.

Offline irk miller

  • DTT SUPPORTER
  • *
  • DTT BOTM WINNER
  • *
  • Posts: 9129
  • You've been mostly-dead all day.
Re: 1974 CB360 Fallin' Ditch Hell Ride
« Reply #195 on: Oct 04, 2016, 04:16:47 »
Anyway...  if I can figure out how to weld up a 2-into-1 collector out of the random shit I have laying around I have my exhaust...




Sent from my iPhone using DO THE TON

Offline Tune-A-Fish©

  • DTT SUPPORTER
  • *
  • Posts: 6844
  • BOTM LOSER Proudly Deplorable
Re: 1974 CB360 Fallin' Ditch Hell Ride
« Reply #196 on: Oct 04, 2016, 08:29:20 »
Should of spoke sooner, I have a few nice ones and some used ones... never make it unless overnight.

"I didn't come here and I ain't leavin"  Willie Nelson

"love hard, live fast, die fun" Kacey Musgraves

"Like a Wreckin Ball!" Eric Church

Offline irk miller

  • DTT SUPPORTER
  • *
  • DTT BOTM WINNER
  • *
  • Posts: 9129
  • You've been mostly-dead all day.
Re: 1974 CB360 Fallin' Ditch Hell Ride
« Reply #197 on: Oct 04, 2016, 08:51:58 »
Should of spoke sooner, I have a few nice ones and some used ones... never make it unless overnight.
Ha.  Much thanks anyhoo.  I have a CJ360 collector.  I'll probably just order the CJ headers to match when I have more time.   For now, I heated and bent these jawns to get me through.  I have enough scrap crap around, I think.

Offline Tune-A-Fish©

  • DTT SUPPORTER
  • *
  • Posts: 6844
  • BOTM LOSER Proudly Deplorable
Re: 1974 CB360 Fallin' Ditch Hell Ride
« Reply #198 on: Oct 04, 2016, 09:54:58 »
Ha.  Much thanks anyhoo.  I have a CJ360 collector.  I'll probably just order the CJ headers to match when I have more time.   For now, I heated and bent these jawns to get me through.  I have enough scrap crap around, I think.

2 chunks of pipe and a belt sander to make a crotch... make the notch cuts and weld the kinks in the 2 after sanding then weld the crotch up with birds beak then cut that off right where the dia is close to the mega slip.
"I didn't come here and I ain't leavin"  Willie Nelson

"love hard, live fast, die fun" Kacey Musgraves

"Like a Wreckin Ball!" Eric Church

Offline NoRiders

  • Posts: 834
Re: 1974 CB360 Fallin' Ditch Hell Ride
« Reply #199 on: Oct 04, 2016, 10:11:12 »
2 chunks of pipe and a belt sander to make a crotch... make the notch cuts and weld the kinks in the 2 after sanding then weld the crotch up with birds beak then cut that off right where the dia is close to the mega slip.

"It's English, but not as we know it Scotty" haha!  :)