collapse

www.dimecitycycles.com

https://www.townmoto.com/collections/vanson-leathers


www.restocycle.com

www.CITYLIMITMOTO.com

www.jadusmotorcycleparts.com

www.bisonmotorsports.com

www.speedmotoco.com

www.lostapostlejewelry.com

www.cognitomoto.com

www.sparckmoto.com

www.Moto-Madness.com

www.pistonsociety.com

www.steeltowngarage.com


Author Topic: Cb360 Reassembly Help  (Read 2909 times)

Online Sderbyshire

  • Posts: 221
  • Into Sailing, classic Triumph cars and motorbikes.
Re: Cb360 Reassembly Help
« Reply #60 on: Jul 20, 2018, 14:31:58 »
Good luck with the clutch, hope it works out.

Where did you source heavy duty clutch springs, i need some for my 390 and have only found ebc here in the uk which i am doubtful of.

Offline cb360j

  • Posts: 54
Re: Cb360 Reassembly Help
« Reply #61 on: Jul 20, 2018, 15:56:35 »
Good luck with the clutch, hope it works out.

Where did you source heavy duty clutch springs, i need some for my 390 and have only found ebc here in the uk which i am doubtful of.


Thank you! I really hope it works as well.

I got my clutch and springs from Barnett Clutches and Cable, this is the link http://www.barnettclutches.com/251/honda/0/0/1975-honda-cb360-g,t.html

Offline raptormeat

  • Posts: 399
Re: Cb360 Reassembly Help
« Reply #62 on: Jul 20, 2018, 22:24:02 »


as a side note, if you remove #25 from this picture, you will never have the dreaded clutch pop again. also allows for a motion pro clutch cable, rather than oem, as that also causes it. (too long outer sheath compared to inner cable).  makes for a nice light squeeze to disengage.
Minimal CB378 Brat
http://www.dotheton.com/forum/index.php?topic=53242.0

DTT Red, White, and/or Black 360 Club - We also discriminate!!

Sexy RD350 Cafe Thing
http://www.dotheton.com/forum/index.php?topic=55882.0

Offline cb360j

  • Posts: 54
Re: Cb360 Reassembly Help
« Reply #63 on: Jul 20, 2018, 23:14:34 »
Remove the lock nut from the clutch adjustment screw?

Offline MiniatureNinja

  • Posts: 424
Re: Cb360 Reassembly Help
« Reply #64 on: Jul 21, 2018, 00:21:35 »
The locknut has nothing to do with anything other than keeping the adjusting barrel screw properly adjusted.
'75 Honda CB360 - thread

Offline crazypj

  • Posts: 13118
  • Split personality, I fake being smart
Re: Cb360 Reassembly Help
« Reply #65 on: Jul 21, 2018, 14:16:21 »
The locknut has nothing to do with anything other than keeping the adjusting barrel screw properly adjusted.
+1  Correct thing to do is remove ferrule and shorten outer cable
'you can take my word for it or argue until you find out I'm right'
Best thing I ever overheard
"yep, PJ's my boss, he taught me everything I know, just didn't teach me everything he knows"
Brian Morgan, 1982

CB360's,  http://www.dotheton.com/forum/index.php?topic=11736.0
XS650,  http://www.dotheton.com/forum/index.php?topic=11922.0

Offline cb360j

  • Posts: 54
Re: Cb360 Reassembly Help
« Reply #66 on: Jul 23, 2018, 20:28:56 »
Anything special I should do before installing new clutch?

Here are some stupid questions

Does the friction plate go in first or does the other plate go in first?
Should the clutch rod be pushed in or out? (Assuming in)

Offline crazypj

  • Posts: 13118
  • Split personality, I fake being smart
Re: Cb360 Reassembly Help
« Reply #67 on: Jul 23, 2018, 21:07:40 »
Soak friction plates in engine oil for 24 hrs. Steel plate should be at back of clutch hub then friction, steel, etc
'you can take my word for it or argue until you find out I'm right'
Best thing I ever overheard
"yep, PJ's my boss, he taught me everything I know, just didn't teach me everything he knows"
Brian Morgan, 1982

CB360's,  http://www.dotheton.com/forum/index.php?topic=11736.0
XS650,  http://www.dotheton.com/forum/index.php?topic=11922.0

Offline cb360j

  • Posts: 54
Re: Cb360 Reassembly Help
« Reply #68 on: Jul 23, 2018, 21:10:47 »
I had read somewhere that it was friction plate first. Glad I asked.
Is there a particular torque the bolts need to go down to in the pressure plate?

Plates have been soaking since yesterday

Offline crazypj

  • Posts: 13118
  • Split personality, I fake being smart
Re: Cb360 Reassembly Help
« Reply #69 on: Jul 24, 2018, 12:48:56 »
The number 1 plater is thicker and 'fixed' to the hub so a friction is first 'movable' plate. I'll get a pic for you
« Last Edit: Jul 24, 2018, 13:05:06 by crazypj »
'you can take my word for it or argue until you find out I'm right'
Best thing I ever overheard
"yep, PJ's my boss, he taught me everything I know, just didn't teach me everything he knows"
Brian Morgan, 1982

CB360's,  http://www.dotheton.com/forum/index.php?topic=11736.0
XS650,  http://www.dotheton.com/forum/index.php?topic=11922.0