Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature currently requires accessing the site using the built-in Safari browser.
We noticed you are blocking ads. DO THE TON only works with community supporters. Most are active members of the site with small businesses. Please consider disabling your ad blocking tool and checking out the businesses that help keep our site up and free.
Thanks for the insight, I will start over again and re-prime over bare metal
As far as pinstripes, would I be better off using some lacquer once my single stage coat is on? It cures much faster than enamel. The single stage should be pretty resistant to lacquer thinner once cured right ...
So... I screwed up a paint job on my gas tank by using Duplicolor High Build Enamel. This paint stays quite soft and did not hold up well to fine line tape when came the time to mask some pinstripes.
Money is getting tight for me on this project. However the good news is that I have some...
Thought I'd share it, it's good for a laugh for anyone who's ever had an XS650, or thinks they want one
http://ottawa.kijiji.ca/c-cars-vehicles-motorcycles-street-cruisers-choppers-1983-Yamaha-XS-650-Real-Bike-for-a-Real-Man-W0QQAdIdZ374078815
"if you fancy something different, and owning a...
This is embarassing...
Went back to the parking lot on my lunch break... No lights at all, no action when I turn the ignition on. Turns out the negative battery terminal vibrated itself off during my ride and the negative cable had bent over time just enough to rest on the terminal. When...
That's what it seems like, because my battery is topped up and everything is fine until the engine starts turning... I might just unplug one of the stator brushes, that should stop any power coming out of the rotor and easy enough to undo...
Thanks for the feedback guys, I'll give this a shot.
I need some quick help...
Rode in to work this morning and everything was going smooth untill the last mile or so... I noticed my idle got lumpy and irreggular, and the lights started to flicker. The bike would stall... Then all my lights were back and very bright again when the engine...
I flipped it for 1200 after riding for 2 summers and 4000 miles, to finance my next bike (XS650). Finished the build with clubman bars / smaller signals / emgo shortie mufflers / a couple of flat black parts. Bike was fairly stock otherwise
Let me know if you have any questions about the...
To get your engine to run, at a minimum, you'll need to wire up the coils, points, condensers, ignition switch and battery. Set the timing and test for spark at each plug... make sure they`re firing in the right order.
I wired my bike from scratch last winter... I can give you some...
If you have the wrong type of oil in the crankcase, slippage will be the issue. However what your experiencing right now sounds more like clutch drag, IE the plates don't release enough to fully disengage the transmission.
Make sure the clutch is adjusted correctly. It's touchy on an XS650...
Has anyone here made their own battery / side covers and can share how to do it? My bike didn't come with them, and I'm using pod filters, I'd like to fabricate or have fabricated something that will hide the battery, but a clean look that fits close to the battery
Here's a couple of covers...
Nice bike!
Do you mind telling me what you did as a battery cover? I need do make one too, but I have no idea where to start. I was thinking one like yours, ie hide the battery but leaved room for the pods
Bike looks awesome. Fork gaiters would look nice on that too !!
Cheers,
Guy
Not sure what exact bike/year you have (CB450??), but usually the points assembly is attached to an advance mechanism. It's a set of springs and weights that allow the points cam to advance 20-30 degrees as the revs climb to make better top end power.
Sounds like a carb issue; easy way to tell it to get the bike to the RPM that bogs down, then pull on the choke some. If it gets worse, you are too rich. If it gets better, you are lean.
Did you check that your spark advancer moves freely? Sometimes they can dry up and seize.
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.