Search results

Was hoping you guys could take a look and give me some feed back on the diagram I made for my CB350 twin. This is using EMGO controls and a fuse box. This is my first go at wiring, so bear with me!

I used some super fine scotch bright pads in my die grinder. Worked pretty well and didn't take very long. I plan to hit it with some buffing pads as well, but will probably wait till the winter time before i go too crazy.

I just went with the VM30's based off of some other posts/build on here. For instance: http://www.dotheton.com/forum/index.php?topic=66352.0 I'm still going to give them a shot and see how well I can get them running. Just because I'm new to motorcycles doesn't mean I don't want to learn...

So I got the VM30's in, just forgot to order a cable. Per the seller they have: 150 mains 159 P-5 needle jets 6F4 jet needles 2.0 air jets 2.5 slides 22mm float 20 pilot jets Also came with: 159 P-2 needle jets 6F5 jet needles 140,145,160,170 main jets 40,45,50 pilots What do you guys...

Thanks for the tips on the brake shoes, really appreciate it. Got a few things done so far, cleaned up the front forks and put them back on. Still need to do a bit more polishing, but it's good enough for now. I'll do more over the winter most likely. My box of DCC goodies arrived, quickly...

Sold to me. 8)

Sent you a PM as well.

I got those coming with my DCC order. 8) I figured I shouldn't take any chances on possibly decade old brake shoes. Quick question on the new shoes though. Anything special I should do to the hub or shoes before I install? Anything after? Knowing that car pads need to be bed in, I was just...

Another amazing build, absolutely beautiful! I only hope my 350 can come even close to looking this good one day. ;) Two questions for ya': - How'd the mikuni's workout (assuming vm 30's)? I'm contemplating it but wasn't sure how much performance improvement you can really expect to see...

Have these on my "want to buy" list. Didn't realize they don't include a wiring diagram, nice work! Bookmarked for future referance.

Last night I planned on just filling the tank up with some MEK and letting it sit and see what happens. I was suprised when I took a look in the tank and saw the lining already pulling away in huge sheets! So I grabbed some needle nose and a screw driver, and I got ~80% of the liner out on the...

Well, I did, up until it the tank lining failed and started clogging the fuel system. So step 1 right now is to get the bike in proper running order and do a few much needed items, like the brakes and coils/wires. Main goal for this bike is to get it cleaned up and running like a top. No...

Bumping my thread from the dead! Things had been crazy in the past year, so I'm finally getting back to this thing. It's my last project to complete before my first child is due at the end of July! So the bike went from the above, to this today: Mainly to fix the failing liner that the...

You have an ETA on these bad boys yet? I need to re-wire my bike, but was kinda hoping to be able to use this!

In for updates!

I placed an order for some replacement mufflers and a few other goodies to get me rolling on some mods. Those should be showing up tomorrow and sometime next week. But for now I've just been puttering around the block on the bike and I've got some issues to work out. My left cylinder isn't...

Interested in the MAC 2-1 exhaust. How loud is that bad boy? Let me know what it would be shipped to 19067.

Hey guys, new to the forum and to motorcycles in general. Thought I would post here since I have a bunch of questions, and this place answered a few of them already. I'm a car guy, but never had anything carb'd before, so bear with me! Recently picked up this for a song off of a coworker...

New guy checking in. Just picked up my first bike, '73 CB350. I'm in Yardley, just outside of New Hope.