Search results

Widest: 11.25" Width at rear narrowest: 7.5" Length without tab: 24.75", with mounting tab: 25.5" Height: 8.5" Tunnel depth at highest: 5", tapers to lowest: 1 3/8" Width widest: 5 1/8", at narrowest: 4.5" Length 21" Sent from my SM-G935W8 using Tapatalk

Not too sure about capacity - I could try and figure it out shortly though. Paid $700 for it, never used or installed once - exact same condition as from manufacturer (fresh welds/no cracks in the glass). Sent from my SM-G935W8 using Tapatalk

Hey guys, Just putting a feeler sale to see if there's any interest for this tank. I'm looking to get it remade in full alloy as I have an alloy cowl and I want them to match! Specs: - continetal style tank, rare - fiberglass shell - alloy tank - stainless steel flush mounted fuel cap -...

Hey guys, I have 2x 2-push button switches from motogadget that are brand new in box, never been used before. I'm looking to see if someone has 2x 3-push button switches that they don't need anymore and would be willing to trade down for mine. Turns out my build requires my controls than...

I know these are a bit of a rarity and hard to find, but if anyone has a set of 1974-1976 Final Drive dampers for the CB550, please PM me! Thanks, Paul

Hey guys, Just got my rear disc conversion hub from Devin @ Cognito, and I love it. My question is, how do these dampers fit in (see attached). I'm having trouble fitting them into the corresponding CNC'd cut-out. I understand there's supposed to slide over the ridge and sit right in, as they...

Hey guys, Just wanted to run an option by you for my first build. I'm pretty far into it, subframe is cut up and I'm about to get a new rim/spokes for the rear wheel. I put a brand new wheel on the front (see picture, 17"), and I have a brand new 150/70-17 tire lined up for the back. 1) My...

Hey guys, Got a few parts from Kinetic Motorcycles (brand new, never installed or used them) for sale, I decided to use different parts for my build so I'm stuck with a few leftovers. Got many other parts too (GSXR lower billet tree/triple clamps/CB wheels/forks, just message me). First is the...

Hey bomorr, Thanks for the advice/links! Do you think sunmate's products would be conducive to seat forming as showing in the picture above? Thanks again! Paul

Hey guys, Just wondering what type of foam you would use if you were going to make your own seat cowl for your own bike. I have a screenshot of some material that's probably similar to what I need, just need to know where to look, Thanks guys! Paul

Hey guys, Coming up to buttoning up my 77 CB550K pretty soon (hopefully, knock on wood). Just taking a look at my camshaft and the bearing surfaces of my head, and was wondering if you guys saw anything out of the ordinary. It's my first rebuild and I really want to do it right. I see a little...

Hey guys, How critical/important is it that you use a CB650 camshaft on a CB550 engine (after it's been bored to 61.5mm)? I've read of alot of guys who have used it, and some people don't. I've had the cylinders bored out to 61.5 and done a full rebuild of the engine, Any advice is...

Nice, thanks work9to5. I ended up getting them bored out to 61.5, my machinist is really good! Did you end up running a 650 cam or did you upgrade any other of your components? Also do you remember ~ what your carbs were jetted to after you bored out your cylinders? That part of my build will...

Hey guys! Just was wondering if anyone out there has bored to 61.5mm on a CB550 cylinder before. Forgive me if there are other posts re; this topic, I was only able to find one. I bought the Jap Bike Spares 600cc 61.5mm Big Bore kit for my 77 CB550K, and am just about the get my cylinders...

Hey guys, Long time reader, first time posting. I'm taking apart my 77 CB550 and I've noticed some pitting on the top surfaces of my pistons after cleaning them, apologies for the picture being upside-down. Being aluminum, I'm wondering if these are ok to re-use or if I should just replace...