Search results

Hi guys, I am having a little trouble with my "clutch actuator". I found a good tutorial online and did everything just like it said, but when I drop it into first gear out of neutral it stalls out before I even release my left hand lever. It is also making a clicking sound when I pull the...

Hi guys, I am having a little trouble with my "clutch actuator". I found a good tutorial online and did everything just like it said, but when I drop it into first gear out of neutral it stalls out before I even release my left hand lever. It is also making a clicking sound when I pull the...

Hi all! So I have a CB 350 and I wanted to take a friend for a ride the other day,but with the both of us on my bike the seat basically touches the back tire...I weigh 180lbs and my friend weighs less than that. Is there something you need to do to the shocks if you have a passenger on these...

Noticed this guy is missing in my clutch set up! Anybody have one? Thanks!!

I had the M-unit working but now just the "lock in" and "Aux out" are lit up. Really confused and would appreciate a little guidance if anybody is feeling helpful. Thanks!

Hey guys realized this might be a better thread to post this on.... Here is the link to the question. Just looking for thoughts on a fix! Thanks! http://www.dotheton.com/forum/index.php?topic=73958.msg877346#msg877346

Hey guys, I just got the m-unit on my bike wired up and there is a faint low hum coming from it after I turn it off. I want to know if I should be worried about this. Also a few seconds after I turn it off the horn sounds. Just trying to understand this thing. Thanks for any pointers!

Hi guys, I just recently bought the M unit and couldn't find how to wire a standard three position ignition key to it. All the diagrams I've seen just show how to hook up the "M lock".Any advice would be greatly appreciated! Pat

So the below link is the regulator/recto. I bought for my cb350. I know two wires go from the starter solenoid to the reg/rec (though I don't know what wire goes to what wire.) it's the same deal with the wiring from the stator , I know the wires are all going where they need to go (to the...

So the CB350 has a few pieces of tube that are part of the stamped frame. What is the OD of CB350 frame tube? anybody want to through a micrometer up against theirs?! :) Thanks!

Hey guys just wanted to share this if nobody has yet! So I want a way to clean up my wires without droping the 250 on the M Box! Check these out for small boats. These look to be a really solid option! Blue Sea Systems ST Blade ATO/ATC Fuse Blocks 12-Circ w/Cover & Neg

So I put my bike together and I was twerking some final adjustments and noticed my foot brake doesn't seem to have enough clearance between the frame and engine to be pushed down very far. I have had around 3 or 4 different CB,CLs of different years in the past, and parts floating around. My...

Looking for this CB350 squared off tank, in close to any condition! Thanks guys!

Here is the noise. It sounds like it's not getting enough juice to turn the engine over but I have it hooked up to a car battery so I can't imagine that's it. Also the kick start is stuck but I don't think that is related because it goes through the gears and rolls fine. Thanks...

Hey I have a 400x18" tire and a CB350 honda 400x19" rim is it a bad idea to try and make this fit? Anybody ever done it? thanks

So I had a guy true a wheel for me. it looks good and it is strait but some of the spokes are a little low in the nipple. I am worried if I hit a large pot hole it could collapse the wheel. Is this a legit concern? Some of the spokes cant be more than a few threads deep into the nipple. Should I...

Hi All, so I have a 71 CB350 and I wanted to lace a new rim for it. I'm pretty sure these originally had a 19" rim on them but I measured the diameter of the rim that came off the bike and it is 20' across. What gives? How are these rims measured? The tire that was on it says 19" Thanks ! Patrick-

So this may be a stupid question to some of you out there, however this is my first engine tear down and I want to cross my "t's" and dot my lowercase "j's". Anyway, I seating the Clutch, alternator and gears back into the case when it occurred to me that there might be a slight possibility they...

I am having a few doubts about what should be torqued and what can be done by hand inside the crank case, specifically the gear shaft screws. Any thoughts? Any help would really be appreciated, I've worked very hard not to screw this up so far. Thank you!

I want to bake the paint on my engine but I am worried about the rubber seals baking at 200º for 1 hour to cure the VHT Engine Enamel. Any thoughts? Thanks!