Search results

Used Mikuni 30mm carb set. Also stamped "83". They are pretty clean, no varnish or gumming. Slides move nicely. Float chambers are clean, floats are in there too. These did not come off a running bike, came with a parts lot I bought during my build. Not sure what else you'd need to set...

Ran these on my Triumph for about a year and now I'm going a different route. Got them from Lowbrow Customs. Decent shape, super-slight pitting in a small area (see pic). Great score if you are on a budget. $40 plus shipping or shoot me an offer.

Installed but never run on the bike. Bought these from DCC but scored a set of Hagon's shortly after. $75 shipped to wherever you are in the USA! Does not come with the different bushings shown on DCC site, only 1 pair which fit tight on my CB450...

I ended up not going the cafe bump route so I'm selling the seat I bought. It's a Road Race 1 seat from HotWing Glass. Check the link for specs. I did start to fit it to my bike so the nose of the seat has about 1" cut from it to make it shorter. $50 plus shipping...

Providing my jugs are within spec, is there any reason why I should pass over a good set of used STD pistons and go for new? Normally me likey the new stuff but we're looking at a couple hundred bucks for that option. ('74 CB450)

1974 cb450. Engine starts easily and runs smooth at idle. Blipping the throttle sounds normal too. Spark is good, carbs have been meticulously cleaned, floats set. It just won't accelerate under load. Just bogs down. Found out the compression on both cylinders is at 120 (well aware 160 is...

NOS if possible. Anything out there? Thanks. -Mike

That's basically it. Mine broke today. Let me know if you have one for sale. Thanks! -Mike

Not sure what to search for so I'li put this out there. Starting this thing up is pretty easy, but as it warms up, the throttle does nothing when you twist it, meaning if I crank on it the engine doesn't rev. After a few minutes the throttle seems to take and I can get going. Then it dies and...

Struggling with this solution. Anyone successfully get a pair of aftermarket mufflers to slip on to CB450 exhaust headers? I have a pair of emgo dunstall megaphones but of course they are 1.5" ID, just like the headers. Shops around me don't want to help with anything they can't pull off the...

OK, so it's easy to see why my caliper didn't want to release the disc, there's a lot of crud in there. Waiting for my rebuild kit from DCC but just want to make sure I've done everything I need to do before reassembly. In the second pic, the port on the right I'm guessing is a return? It...

Bought this bike for the engine and some bits and pieces. $75 obo seems fair. Will need to discuss shipping cost...not sure if I can slap a label on it or if it would need to go in a box. Located in zip code 07718. Pick up available there or where I work (08832).

OK, bought this CB450 last September. Motor kicked over VERY easily. Was able to run the engine but it was tough to keep it going due to 1 carb not fueling and murkey, rusty gas from the tank. Thought that was enough to begin the build. Fast forward to now, most of the bike is back together...

So I'm stalled with m Honda build and took my neglected Bonneville out for the first ride of the season (way late I know). Since I didn't cut the original muffler mounts of this bike I want to finally grab some rearsets that I can bolt right up. I was searching thru the boards but didn't see...

Mines cracked and leaking...I know there's someone out there that has one sitting in a milk crate. Let me know what it's going to cost me. Thanks!

Fine specimen. 19", 36 spoke. Missing the brake strut. PM me with any questions. I'm looking for $60 (OBO) plus whatever the shipping cost is to your location. Box is big and heavy so USPS may be the cheapest option. Thanks. -Mike

I have this rim, 40 hole setup for drum brake. Looks like it is destined for paint or powdercoat as it has been partly blasted. There wasn't any pitting on the outside but the inside along the bead is pretty nasty, see pics. If you think that won't be a problem, I'm looking for $25 plus...

I'm guessing it's time to start a thread. Picked this bike up in October for $650. Couple dings and dents as well as some surface rust on all the chrome. Came with a title from original owner so I was going home with it no matter what. The guy started it and it sounded a little choppy so at...

Looking for a 19" drum setup to ditch my disc brakes. PM with price. Thanks!

Hey everybody. Been trolling the site for a couple days and i like what I see. I currently have a '72 Bonneville which I plan on making into a cafe. Sor far, I just removed all the non essential and added clip on bars but I'm looking to add a cafe seat and drop some more weight. Anyway, great...