Search results

1976 CB750K. Finally got my bike running so I was cruising around a little and I'm only running on 3 cylinders. Exhaust #3 is dead cold when all the others are hot. It's getting a good spark. So next I pop off my pod filter to carb#3 and spray some engine starting fluid in there and what do...

So I took my transmission cover off to fix the oil that was always dripping out. Laid some liquid gasket down and slapped it back on and now the shifter feels really weird. I can shift through all the gears but it takes a lot more effort than before and doesnt spring back to position. It just...

So I'm the typical douche that put pods on his bike ya ya. Im also running open headers. I want to get some sort of small baffle or something just to give it some back pressure. I cleaned and rebuilt the carbs and I had 110 mains and 40 slow in and it ran well overall but was pretty lean. I read...

i've got a '76 CB750 with frayed spark plug wires, and the wires are built in to the coils so I have to replace everything. Everything I've heard says go Dyna, and I need the 5ohm with my stock ignition. Does this sound right?

I recently came into a CB175 for cheap. A new battery and a petcock cleaning and now it starts right up and runs. Except it will randomly rev up really high for 10 seconds every 45 seconds or so. Then it will go back down. The throttle isn't sticking. I wont' touch the throttle and the revs will...

Finishing up the build on my '76 and stopped by the tag office to see what it would take to get a tag. I don't have a title so I was worried it would take a lot of time and money and filling out paperwork. Lady told me all I needed was the bill of sale and proof of insurance and I could walk out...

Just posting this to give someone ideas. It's a pretty simple system and it's cheap so it's not hard to do. I know I was really worried about mounting mine because I'm no fab master and spent forever looking at different brackets, but in the end I didn't need any of that. Used Dime City's...

So I bought Carpy's stainless steel braided oil lines ince my old crappy ones leaked. His has tons of pics of them on SOHC CB750's. These are the ends. However my oil tank has a male thread. And I'm not even sure about the end on the engine. One of the heads is stripped. Go figure! Are...

My bike is pretty well done (minus paint) except for my front brake! I have a 76 CB750k, but I think my brake caliper is off a different model or year because when I bought my new piston and brake pads I remember having to return them and get different ones. Anyways, the bracket between the two...

Guy started out asking 6500 or something over a month ago and now he's down to 3500 http://atlanta.craigslist.org/atl/mcy/4114977451.html

Trying to decide between 1.9" or 2.5" and I'm not sure which would be better. I plan on running both a speedo and tach on my 750. If you could include pics of your setup that would be awesome. Thanks!

My new tank has 2 petcocks, one on the left and one on the right. I've got a CB750 so 4 carbs. Should I run a line from the left petcock to the 2 left carbs and the right petcock to the 2 right carbs? Or bring the 2 petcocks together and then run 2 lines from that joint to the left and right...

If I'm running open headers, or more likely putting a shorty muffler on, does it really matter too much what exhaust I get? I've been looking at the Mac 4-1 for my 750, and I've heard some bad things about it, mostly good though, but if all I'm using is the headers does it matter too much what...

1976 Honda CB750k...I've searched on here and read way too much online and still haven't figured it out.. my eyes hurt. I know this isn't a hard job to do but I just want to make sure I get it right. I checked the Steering Stem Bearing Sizes list thread here and the sizes (Upper 26x48.5x15.2...

Finally got my Gus Kuhn tank from DCC. It is fiberglass with a black gel coat finish according to their site. I was planning on just being able to shoot it with paint and clear, except there are a bunch of deep chips in the finish, a residue around the edge like there had been pin striping that...

I was look at the Gus Kuhn tank on DCC, and then came across the above picture on google. Are they the same? Or is the one pictured an older tank? Here's the link to the DCC tank...

I am looking at these rear sets from Dime City for my CB750, and I want to keep my passenger pegs. So since most guys just put rear sets where the passenger pegs were, could I use these rear sets and mount them somewhere else? So my question is, is it just up to me to fab up some sort of bracket...

I can't be the only one that wants the classic cafe look with the hump on the back, and still wants to take the girlfriend for rides. I'm pretty small, 5'11" with a 30" inseam and my gal is very petite. Do you think I could fit her on the back if I got this seat? I'm ok with us being cramped and...

I was rebuilding the front brake for my 1976 Honda CB 750K and ordered a new piston, piston o ring, and brake pads for that model, but they are all too small. I did a little sanding on the outside of the caliper assembly and found "K5" stamped into it, but the 750 K5 should have the same brakes...

About to order a new o-ring 530 chain, but I'm not sure how many links. I think it's 100 but I also heard 102. Going to go on with new stock 17/48 sprockets I was looking at this one...