Search results

Can anyone point me to the right cam chain master link for a 71 cb175. I was under the impression that I am looking for a 219h, but when I saw the one on DCC, it looks different than the OEM one.

Can anyone confirm that this is the correct Time-sert kit I need for a '71 CL175? I have 12mm x 1.5 (pitch) for the thread dimensions. Is the 9.2mm insert long enough? http://www.amazon.com/TIME-SERT-Metric-Kit-Part-1215/dp/B001JK44D4...

Can anyone verify the spoke "nut" size for a 71 CL175? I'm on fleabay and a few other sites looking to pick up a spoke wrench.

Definitely agree, they look to be supporting the under side of the valve springs, which on the exhaust side is the only thing between the head and the springs whereas on the intake side the valve seat (#15) appears to do the same job.

On the '71 CL175s are the washer-like valve seals only on the exhaust side? I'm reassembling the head and I thought I was missing a set until I looked at Bike Bandit's parts diagram. Can anyone confirm this? Parts #17 & 16...

Re: My CB200 BUILD - THE RESURRECTION - SHOW N SHINE PHASE I thought you parted this bike? ???

Thanks guys! On a side note the ebay seller I bought the rings from is sending out a new set free of charge!

Just snapped a new ring :'( and wanted to see if anyone could recommend a somewhat low priced expander that would work on CB175 piston rings. Would something like this work...

Re: '71 CL175 - Stretched tank preview Let me know if you still need the side sprocket, I have an extra one laying around. Also, which fender are you looking for I have 2 front and 2 rear CL175 ('71 K5) fenders in pretty good shape.

I bought these ones for my 71 CL175 and they worked out great. http://www.ebay.com/itm/300770776947?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1439.l2649 If you need individual specs you could probably check out Bike Bandit or Western Hills Honda.

http://www.ebay.com/itm/CB175-CL175-HONDA-RIGHT-CONTROL-SWITCH-NEW-OLD-STOCK-BY-FCS-/360488825535?pt=Motorcycles_Parts_Accessories&hash=item53eecef2bf&vxp=mtr

Looking for a CB175 tank that is in somewhat decent condition (at least restorable)

Would this coil work? http://www.bikebandit.com/emgo-points-style-ignition-coil Bike bandit says it wont "fit", but I'm not worried about whether or not it will physically fit, more concerned about it's functioning.

Anyone have access to a digital copy of clymers for a cb/cl 175?

I was planning on lapping the valves myself, but taking the cylinders in to get them honed. This is my first rebuild, so I'm finding that my plans change from day to day, so I may consider new stock valves, new rings (once I figure out the size of the pistons) and taking it in to get it all...

I have a 71 CL175 K5 and I'm currently doing a top end rebuild. I took the pistons out and noticed that there were some numbers on the side. 313 & 3 and 313 & 4 (on the other one). I am about to purchase some rings and wanted to make sure what size pistons these were. I looked up parts number at...

I have another cylinder block that came off a parts bike. There's more light surface rust on it, but very little pitting, downside is that one of the fins has a little knick out of it and there are scuffs all over the outside. I'll take both to the machine shop and see what they say. If I...

In the process of banging out seized pistons from the cylinders I dinged up the top of the cylinder wall. I am planning on getting these honed, but want to know if these are even salvageable and if the dings will cause any damage down the road (concern for weak spot in the gasket at this point??)

Thanks M!

Thanks for the feedback! If I were to replace with a universal coil I would just be looking for a 12v 5ohm dual fire coil? Would something like this work...