Search results

I have a 1973 cl350 head that needs completely reworked. Valve guides surfacing. Can anyone point me in the right direction for this type of labor? Thanks for the help. youngn

Good afternoon all, I have a set of rims are rusted beyond saving. I wanted to clean the rust off and powder coat. Is this advisable? Would I have to plug and cover the spoke holes so that there would not be any powder in the divots and spoke holes to break away and cause the spokes to...

Good afternoon, I had to replace my battery in my 1979 CB750k. After replacement I tried to start the bike and all I got were dim lights and a click from the starter solenoid. I did a little research and cleaned the terminals both positive and negative at the engine mount and terminals I also...

Good morning all, I have a 2002 KTM EXC 520. It has WP front suspension. I need to replace the fork seals and have been looking for some type of guidelines or a manual for taking these down and putting them back together. So far I have not been able to find very much info at all on this...

Good morning all, I am looking to buy a complete head, valves, springs and rockers for a 1973 Honda CL350. Assembled if possible. Let me know what you have. Thank's, Young'n

Good morning all, I have just picked up a 1995 CBR900RR for next to nothing. Previous Owner needed to get rid of it. Main problems are that the transmission needs replaced, he included an Ebay used transmission which looks good, and all of the plastic has been either wrecked or removed, except...

Good morning all, Just a few quick questions. I have a chance to purchase a 1977 CB750 for around $700.00. So far the bike runs, carbs need cleaned and spark plugs need tightened. The far right cylinder spark plug is either loose or needs to be re threaded. it seems to have pretty good...

Hello All, Just getting back to work on my CL350 after an extended leave of absence. I am in need of a complete head for my 1972 CL350. I have a head but it needs new everything and I don't have the money to have it reworked. Does anyone have a head that is ready to bolt on or maybe need some...

Hey all. I am looking for a 1979 DT 400 motor for replacement of my current motor. How much should I pay for a running good condition motor? And what is the availability of these. Thanks in advance for the help.

Good morning all, I have a 1979 CB750 that will not cold start. I have checked for air leaks and did not find any. Battery is fully charged and starter spins like a top but it acts like it is not getting a good spark. When it is warm it starts just fine. Next for me is to change the plugs...

Good morning all, I have the opportunity to buy a 1995 CBR900RR with about 15000 mi on engine, transmission is shot, but he has a new transmission ready to go back in. The bike is fairly clean. No major issues besides the transmission. I was looking to get the Front and rear end off of this...

Good afternoon all, I am trying to up load a picture. What is the max size I can upload. The bounce back is telling me that it is taking to long to upload or Pic. is to large. Thanks

GOOD AFTERNOON ALL CAN ANYONE TELL ME THE BEST WAY TO STRIP PAINT OFF OF FIBERGLASS?

I looking into buying a Suzuki GT750 from a friend who wants it gone. Here is what I know. There is no title, however if after the DMV inspection proves that the #'s are clean I can get an antique title. The bike kicks through and seems to have good compression, the gears shift smoothly, the...

Good morning all, I have the heads off of my 1972 CL350 these were seized up, and after I freed them, the right side cylinder is pretty rusted and pitted up. I need to have these bored and honed and pistons matched. I do not have a machine shop that is local. South Eastern Kansas. Where...

Hello all, I have been lurking or trolling for a while and have received some really great help and info. off of DTT. I thought that some of you would appreciate this. At least it's good for a laugh anyway. This I am saying with knowing just enough to get me in trouble. I have been looking...

Does anyone know what this tank is or where it is made? http://cgi.ebay.com/ebaymotors/Honda-CB-Honda-CB-750-Cafe-Racer-Completely-Restored-/271180237231?pt=US_motorcycles&hash=item3f239a09af Is it stock?

Does anyone know what tank this is or who makes it?? http://cgi.ebay.com/ebaymotors/Honda-CB-Honda-CB-750-Cafe-Racer-Completely-Restored-/271180237231?pt=US_motorcycles&hash=item3f239a09af Is it stock?

I am looking for a 1972 CL350 Cylinder head or anything compatible. Can any of you help me out here I have found a few on Ebay but wanted to check here first. My original head is to pitted up to work. Thanks for the help.

My question is about heads. I pulled the engine on my CL350 to get the piston unstuck. Tore down to the pistons to find the right hand cylinder rusted in place. I used a method I had read about here and on hondatwins to un-stick the piston which took about a 1/4 cup fuel 1/4 cup A.T.F. and an...