Search results

We have a number of fiberglass fairing and seat moulds for sale. They were built by composite professionals, are in good to great condition, only need a coat of mould release wax and they are ready for use. In some cases, the mould price is less than the cost to buy the part. Pick up in...

I'm posting this for a friend. Pix can be found on the CVMG website, "motorcycles for sale" section. Please contact Bill directly. "I have converted our Honda Ascot SOS racer into an eligible road racer for Period Three - Light Weight Superbike complying with VRRA, AHRMA, and USCRA rule books...

This ad is probably more for our Canadian members, as shipping to the US may be a bit steep. The sprockets are NOS, in the original package in most cases. They have JTF part numbers marked on them (see the photos), but some are from other manufacturers, so you may end up with a Renthal (or...

I'm working on a couple of early '70's Kawasaki F7, 175 cc. street / enduro bikes and want to respray the engine side covers with as close a match as possible to the silver paint that Kawasaki used. Any suggestions? Thanks, Patrick

I'm looking for a 1970's RD125 complete rear hub, including brake backing plate and arm, axle adjusters and sprocket carrier. I would consider a complete rear wheel - not worried about the sprocket, rim or spokes condition as I will relace the wheel and buy a new sprocket. Some of the small...

I've an old Kawasaki enduro carb I'm working on - very clean inside and no issues except for a missing float bowl gasket. A DPO had tried to use some sort of sealant, which lasted about a minute before it started leaking. Has anyone found sheet gasket material that works for float bowl gaskets...

I'm posting this for friend and retired road racer Wayne Raynard. Really fast back in the day and obviously a real pack rat today LOL. Some great stuff at excellent prices. For additional information, photos, whatever, contact Wayne directly using the email listed. The stuff is in St...

SOLD Fiberglass Seat, TZ250 Yamaha H / J / K Style New Old Stock. Never been drilled or mounted. Was a spare for one of the race bikes, which was sold years ago. Same shape and profile as a standard Yamaha TZH seat except the seat base hump has been reduced in height. Yellow paint job has some...

SOLD New Old Stock. Never been drilled or mounted. Was a spare for one of the race bikes, which was sold years ago. Same shape and profile as the original slipstreamer seats from the ‘70’s, but with a flat seat base. Sturdy construction, in white gelcoat. Two tiny little chips in the gelcoat at...

My friend Lou has his 1973 Triumph Bonneville Cafe bike for sale. It features: Aluminum tank& seat Electronic ignition Electronic voltage regulator Engine totally rebuilt - I mean totally, all new Kibblewhite valves, springs, guides, fresh rebore .020”over pistons, rings, every bearing...

A few photos of #570 Hack were posted on the chat room. Got a couple of photos from Dave last night, couldn't get then to post on the chat room, so here ya go. Pat

I started looking at fuel tank safety foam again after a previous post here and wondered how many people use it, their experience with it, etc. etc. etc. I was going to post a few comments on its use, but intended post ended up being a bit wordy so I thought maybe I'd listen first and post...

Hi all, Posted something similar on the VRRA website but seeing as a lot of you don't go there, well, here ya go... Was ****ing around with one of my 175 Honda twins today, checking the ignition and the advance, blah blah blah. Anyway, my understanding of the ignition advance on the bike is that...

87 CENTS I was told this story by a friend of a friend of someone I know, probably 5 years ago. I have no reason to doubt the facts as stated and if anything, I think it is more pertinent today than ever. I live in the Toronto, Ontario, Canada area – a big city with big city problems. Homeless...

Hi all, Also posted this on the VRRA site, but seeing as not everyone goes there, might as well share the joy. Was getting ready to install a couple sets of wheel bearings today - mine are "2RS" - ie., rubber seal on both sides and... just for shits and giggles - and 'cause a really good bike...

Hi All, Have been tinkering with my '77 GS550 again and one of the upgrades I'm pondering is to go to a mag-type wheel set. Have done a bunch of other mods to the bike and thought wider / more modern rims would be neat - I love the look of the old '70's superbikes with Dymags, but those are...

Happy Canada Day Everyone! As the subject line says, looking for a set of ignition advance springs for my CD175. CB/CL/SL are probably all the same, like the points. Years ago, I could buy various tension springs to tailor the advance curve, but Gerald Ford was still president LOL. The only...

Happy Canada Day Everyone! As the subject line says, looking for a good set of ignition advance springs for my CD175. CB/CL/SL are probably all the same, like the points. Years ago, I could buy various tension springs to tailor the advance curve, but Gerald Ford was still president LOL. The...

Hi all, We're having our "End of the Road" sale on all remaining Pacomotorstuff fiberglass parts at the CVMG National Rally in Paris, ON this weekend. Fenders are $55.00 including tax, so almost 50% off list price in some cases. Seats are $115.00 including tax, so savings of 25% to 40% depending...

Hi all, I've attached a couple of photos of a nice CB750 SOHC cafe racer that won Best Cafe at the recent Toronto Spring Motorcycle Show. The photo of the fat old bearded guy is me, taken a couple of months ago and the other one was taken when the award was presented at the show There is a nice...