Search results

Use a 0704^ Harley rim, thats what i did. Same diameter axle as the gsxr http://www.dotheton.com/forum/index.php?topic=62861.msg848203#msg848203 http://www.dotheton.com/forum/index.php?topic=62861.msg872020#msg872020 edit: added link and corrected the year

Awesome, thank you so much! Great! I love options

Do you have a source on these pistons? I used the google machine without success.

We also strapped a ratchet strap for full compression of the front suspension on it the other night and there is no interference. Thanks for the insight btw. It can get overwhelming the stuff that may be overlooked. I appreciate it. Ahh good point on the drive shaft, thank you. Once I set the...

I didn't realize that in the picture, but it is definitely the angle. There's gobs of room. I looked through the pics and I don't have another that really shows it, but all is good. The setup is really good. This is a little better angle, but there's even more room than what this shows:

I figured I would update this post with some new things I got the stem sorted out by making 2 adaptor rings, one for the top triple and one for the bottom. Both press fit. These adapt the old stem to the new clamps on the 09+ forks. The old stem was then pressed into the bottom adaptor. The top...

Sold brother! I'll pm you my details

Yes if it's intake valve and within specs it's sold. Only got about a month of riding left and would like to get it back on the road.

I agree that they are out there, I just want 1 intake valve that doesn't cost $70. Used in good condition is what I'm looking for first. If that fails I'll check your source, thanks This is actually tempting, however, I'd have to find the right person to do the machining. There's literally no...

I am in need of (1) intake valve for my CB360 head, PN 14711-286-030 SEE HERE: http://www.dotheton.com/forum/index.php?topic=74339.0 This the immediate need to get my bike back running, however I will also take a full set intake/exhaust if the price is right. CB350 and CB360 are interchangeable...

Sorry I totally flaked out on this question, I actually never saw it, but yes that sounds correct

Awesome! looks solid man!

Does anyone know if it is recommended to replace the washer after removing and replacing the head. It appears to be a crush type seal copper waher, part# 90441-329-000 #13 in the diagram

Good tip, thank you. That's a bummer, man. Ugh, these little engines are temperamental at best. I'm gathering the general consensus is that we are all crazy for maintaining them, hah. At least parts are somewhat available. My local Honda shop did not have an intake valve available, however. I...

I guess it must have backed out. That's crazy because I haven't adjusted the valves in over a year. Haven't put the miles on it to need to adjust them and the bike ran great. Oh well I got the head off and the broken and bent valve out. The hard thing is going to find just one valve to replace...

Thanks! Any ideas what would cause that though? I don't want to replace the broken valve and have it happen again.

Tappet screw was by the spring, fortunately. And I have no idea how to get the valve out.

So this happened... Everything was fine and I was out on a ride about 5-6 miles into it I lost all power. Previous to that I was on the highway ~65-70mph. Got about a mile down a side road and that's when I lost power. Towed it to my dad's and found out the left cylinder was not firing. OK not a...

Is this some proprietary gps chip for these gauges only? All a gps chip is going to do is provide NMEA data that would then get parsed by the processor. I developed a digital gauge gps speedometer with screen from a very cheap chip, but the internals are all the same, UBLOX neo 6 or 7 are...

Draftsight for 2D sketches and Solidworks for 3D modeling