Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature currently requires accessing the site using the built-in Safari browser.
We noticed you are blocking ads. DO THE TON only works with community supporters. Most are active members of the site with small businesses. Please consider disabling your ad blocking tool and checking out the businesses that help keep our site up and free.
F/S: 1974 Honda CB360.
Stock motor/carbs
Custom intake
Hard tailed
Sportster gas tank
Rear fender from 1930's ford spare tire cover
Spring leather seat
Kick start only
Custom covered wire harness
Harley 12" ape hangers
Harley controls with new lines.
New tires/ tubes...
Have a few issues getting my CB360 running properly.
It will start, idle. and run for about a block them will fall on its face when load is applied and die. I can get it restarted. And will do the same thing.
If i let the bike idle for a minute, it will eventually not respond to throttle inputs...
This might be a stupid questions. So please excuse me and tell me to piss off, if need be.
Do I need to reconnect the high lighted wire to my neutral switch if i don't have a neutral light?
I am in need of a set of solid handlebar riser bushings.
Anyone know of who sells them?
Bike: '74 Honda CB360.
I am using 1" bars with Harley Risers uses 1/2"-13 bolt. So the through bolt is larger than OEM.
I saw these but i'm not sure if they will fit a CB360 or not...
I am going to have my tank/fender powder coated (the picture attached is the color I'm planning).
Can anyone recommend a filler I can use prior to powder-coat to smooth some imperfections?
Thanks in advance!!
Sent from my iPhone using Tapatalk
Electrical isn't my strong suit. I drew up my wiring diagram for my '74 CB360
I tried to be as detail as possible. I am thinking i'll prob. use 12 ga. wire.
Any suggestion or changes are greatly appreciated!!
I am switching over to EMGO Universale Coils from DCC. I have no idea if those are...
I am working on a design for a Airbox on a '74 CB360.
It will bolt into the stock tool box mounting tabs.
It will have brass screen--> uni-filter pre-filter-->a cut up 6" wide K&N pleated filter.(or build a filter from bulk uni-filter foam)
The end caps will be drilled to allow air entry.
From...
I am thinking of using these tires front/rear on my '74 CB360. Do you see any issues with running these?
They are 3.00 X 18"
http://www.jpcycles.com/product/210-089
I am going to try my hand at free hand pinstriping. I started this week, It is def. going to take a while to get proficient at it.
One thing i have learned after reading is start opposite side that you are painting with. That way you can see what you just did..
I didn't read that until after I...
I am building a '74 CB360. I am planning on using 1/4" Brass Tubing/Brass double ferrel compression fittings for my fuel line.
I have googled it, and haven't really found a answer.
Has anyone on here, used brass tubing for there fuel lines? Is it a good practice?
Can anyone point me to the...
Thinking about snatching up this helmet, since i found it online for under $60 shipped.
Anyone have this helmet? What is youre opinion of the graphics?
Does it look better in person? I get conflicting pictures of the actual color. Ranging from Olive green to neon green.
Also how does the 3/4...
Figured I'd show off some of the stuff I have drawn up in CAD, and parts I have made.
Velocity Stacks:
Light bar/skid plate for Subaru
Header for a F250 Diesel
Punisher Engine Covers
Chrome Shift Rod:"Making chicks cry since 1973"
530 Chain Tensioner:
I have few left over parts from my CB360 built
Swing arm
Rear section of the frame
center stand
Hand controls
front brake switch
headlight bucket with lense
seat(torn cover)
Rear fender
Shoot me a offer on anything you need.
I am looking for either straight or upswept(prefered) chrome cocktail shaker exhaust. I will need a pair (left/right)
If you have a set your looking to sell please let me know. Also looking tan header wrap.
I have a '74 honda cb360.
The front brake mount is suppose to pivot smoothly.
Except mine when I move the arm. It will stay in the position i left it in.
I remove the arm from the fork, and it is very hard to move the arm. I have put some penitrating oil on it, and it seems to have free'd up...
For Sale: Brand New TC. Bros 20mm axle plates.
I purchased the Universale Hardtail kit. But the axle slots are too large for my CB360 project, so I had new 17 mm axle plate laser cut.
New $29.99 + shipping, I'm asking $25.00 shipped to lower 48.
I'm open to trades or offers...
My current project is a '74 Honda CB360. But has no title. And before I go about getting a title. Does anyone have a good CB360 Frame with a title that they would part with.
Please shoot me a message with a price.
BTW, i live in Eastern Iowa.
I got this bike from a good friend of mine who had it hanging out in his shed, that he used as a parts bike for his previous CB360. For the low low cost of one beer.
Here is my other bike a '06 Yamaha Warrior.
My plans for the bike are to turn it into a hardtail bobber. I have a welder @ work...
Hello all from Iowa,
I aquired a '74 CB360 from a good friend for the price of (1) beer. Has almost everything I need, missing things I was going to replace anyway. But first thing to tackle is it has no title. From my understanding is Iowa is pretty slack about getting a new title.
I am...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.