Search results

Hey all, I have a 1996 cb750 that ive been wrnenching on. It is no where near finished, but is at decent stage. Stock, it has an electronic tachometer. It has one wire that goes from the tach to the Ignition control module (see below), color code is Y/G (yellow/green). So with the...

Hey guys. Check out my eBay auction for this used conversion stem from Cognito Moto. Hit me up if you need it. http://www.ebay.com/itm/-/112474939683?

That's what MAC and Dime City Cycles say. I'm sure they know.

Thanks!!!

Hey guys I have the above exhaust system for sale. Currently brand new this is around $500. I have a used one for sale at $350 plus shipping. Fits: CB750 F/C 79-82, CB750SC NightHawk 82-83, CB900 F/C 80-82, CB900 F/C 80-82, CB1100 F/C 82-83 Let me know if anybody has any questions...

Hey guys, I am hoping this will be the last time rebuild this engine (1980 cb750k) for a while. However, each rebuild I get to know this baby even more. One of the things I will be replacing are all the bolts for new modern hardened bolts to reduce stripping and bolts snapping. Where can I...

Okay I will try and report back. Thanks for the reply.

Okay guys, I have been trying to get these things to work to no avail. I have a 1980 cb750. It has a brand new wiring harness, after market bulb front turn signals and an led all in one tail light/turn signals. I have upgraded the flasher relay to a three prong LED relay. I had all the lights...

I love that seat. I wonder if that will fit my K model?

Such a sexy look! I think those gold forks on a vintage bike. I'll send you some measurements this weekend on the rear wheel shims. Sorry its taking me longer than I wanted.

Huh okay. Man there is so much to learn on these vintage bikes, like this noise and that noise etc. Okay Psycrow, what do you think, besides the popping on deceleration it feels like it runs rough in the lower gears (1-3) under 4000 RPMS and then in the higher gears sometimes I get some...

I'll just use the stage 1 set up because I am using the stock air box and the aftermarket exhaust. I'll see if that helps.

Okay I am pulling the carbs off this weekend. On the MAC exhaust I have a cone engineering cone muffler. It cuts the noise down quite a bit but is not as restrictive as the MAC muffler. I need to replace the float bowl gaskets (I got some Randaak gaskets) because I've got some gas slowly seeping...

So I will be checking the exhaust tomorrow. It is a one piece MAC 4-2-1 exhaust and was very difficult to get on and in position. I've got it tightened down, but can still see some brass exhaust gasket peeking out from behind the headers. Is there any other way to tell if your exhaust is not...

Okay guys, I rebuilt the top end with new rings, new exhaust valves and set the valve clearances to within spec, most are right at .003", a couple are at .0025" and one is at .005 and .006". The ones that were really out of spec I replace to bring them within acceptable ranges. I just synced the...

Hey I've got a link to a real good video that covers converting stems for GSXR trees and CBR trees if you want to do it yourself. Check it out. http://honda-cb750-s.456789.n3.nabble.com/How-do-swap-any-front-end-on-to-any-bike-video-td4058328.html#a4058368

Hey I saw your thread and thought I would just comment on the Cognito Moto conversion stem. It works amazing. I have a 1980 cb750k that I through on the conversion stem with a set of 2005 Yamaha R1 forks and wheel. It was about as smooth a process as you can get. True bolt on. The conversion...

Welcome! That's a beauty and especially for the price! Can't wait to see what you do.

Okay quick update. Thanks for all the replies. I have headlight hi/low running perfect. Tail light and front brake switch works perfect. Now. I still don't have turn signals and with what you said adventurco I am wondering if there is something going on with the left hand control switch so I...

Okay, I have a 1980 cb750k that has gone through quite a few revisions. From stock I tore it down and added LED lights, LED flasher relay, café bars, rebuilt forks etc. It was fun, everything worked, except the engine was gutless. This time around I have Converted a set of 2005 Yamaha R1...