Search results

Hey all, I have a 1996 cb750 that ive been wrnenching on. It is no where near finished, but is at decent stage. Stock, it has an electronic tachometer. It has one wire that goes from the tach to the Ignition control module (see below), color code is Y/G (yellow/green). So with the...

Hey guys. Check out my eBay auction for this used conversion stem from Cognito Moto. Hit me up if you need it. http://www.ebay.com/itm/-/112474939683?

Hey guys I have the above exhaust system for sale. Currently brand new this is around $500. I have a used one for sale at $350 plus shipping. Fits: CB750 F/C 79-82, CB750SC NightHawk 82-83, CB900 F/C 80-82, CB900 F/C 80-82, CB1100 F/C 82-83 Let me know if anybody has any questions...

Hey guys, I am hoping this will be the last time rebuild this engine (1980 cb750k) for a while. However, each rebuild I get to know this baby even more. One of the things I will be replacing are all the bolts for new modern hardened bolts to reduce stripping and bolts snapping. Where can I...

Okay guys, I have been trying to get these things to work to no avail. I have a 1980 cb750. It has a brand new wiring harness, after market bulb front turn signals and an led all in one tail light/turn signals. I have upgraded the flasher relay to a three prong LED relay. I had all the lights...

Okay guys, I rebuilt the top end with new rings, new exhaust valves and set the valve clearances to within spec, most are right at .003", a couple are at .0025" and one is at .005 and .006". The ones that were really out of spec I replace to bring them within acceptable ranges. I just synced the...

Okay, I have a 1980 cb750k that has gone through quite a few revisions. From stock I tore it down and added LED lights, LED flasher relay, café bars, rebuilt forks etc. It was fun, everything worked, except the engine was gutless. This time around I have Converted a set of 2005 Yamaha R1...

Hey guys, I am rebuilding a 1980 CB750K and somehow the right fork holder on my lower triple tree got bent. I purchased a 1979 CB750K steering stem/lower triple tree from eBay thinking they are compatible. When I put it on I realized the stem angle was different and my top triple tree would not...

Hey guys I have a set of 35mm standard Tarozzi Clip-ons for sale. These were only installed on a set of forks, than taken off. A couple really light scuffs as seen in pictures. $100 free shipping.

For sale is a 2.5" mini tachometer with black face and black steel finish purchased from Dime City Cycles. This is a 1:4 ration for your larger CC bikes and has the bright white LED backlight. This is brand new in box. I bought this to put on my cb750 but now I need to sell it. $50 and free...

So I am using Red Kote on the inside of my gas tank. I have a gas tank stop that has a lot of surface rust and a bit of pitting. I cleaned it off with some rust oleum goop and then wire brushed the pitting. Now to permanently keep the rust off, do I need to paint it? Currently it is covered in...

So guys, on the engine, the little screw that is suppose to thread in, does not grab any threads at all! I was thinking it must be too skinny of a screw but I am not sure and could not find it in my Haynes manual, what the original screw size is. To me it looks and feels as if the bolt has a lot...

Hey guys, anybody ever heard of these? Used them? Chains made by Forward Powersports. They are around $50 for an O ring chain. Also, whats better, O-ring or X-ring?? Thanks...

Hey guys I have my engine out of the frame for cleaning and want to turn over the engine. Which side cover do I take off the get to the bolt in order to manually turn over the engine. Like I said NOOB question. Thanks!

Was on YouTube today and ran across this on the Moto Channel. Immediately fell in love with this Yamaha Virago by Stanley Tang! I think he's on this forum too. I've always been intrigued by this classic V-twin and love it when it is made into a cafe bike. Just had to give him a shout out for...

I am rebuilding my 1980 CB750K and noticed the MPS-200 spark ignitor has been dripping in the past. There are several black drip spots on the battery box and on the swing arm (see pictures below). Does this mean they are going bad and that I should replace them? Thanks!

Okay guys, so I just finished stripping down my 1980 CB750K to the bare frame (getting ready for some sandblasting) and I had been meticulously putting every part in a box for safe keeping. Well, I didn't do a good enough job and this piece (see picture below) was laying on the cardboard...

Hey guys, I found these regulator/rectifier and stator for a pretty low price from Caltric. Has anybody used them? This would be for my 1980 CB750K. http://www.caltric.com/catalogsearch/advanced/result/?category=4&make%5B%5D=7&year%5B%5D=78&model%5B%5D=6508

Okay, I am stripping down my 1980 CB750K to get the frame, tank and wheels ready for a little sandblasting. I am looking at the wires and noticed most of the plastic fittings are very brittle and crumble when I put pressure on them (just to disconnect them). I have pictures below. Do I need to...

I am rebuilding my 1980 CB750K and noticed the MPS-200 spark ignitor has been dripping in the past. There are several black drip spots on the battery box and on the swing arm (see pictures below). Does this mean it is time for a new one? If so where do I get one or a replacement one? Also...