Search results

Hi all, finally got my first bike (CL350k3) running and have a few small things I have to do to get her road ready, but since I live in Michigan, looks like that's not happening before winter. My question is this: I spilled gas on my tank (rattle can job w 6 layers of clear coat) and the clear...

Hi everyone, Unfortunately I had things other than my bike that needed attending to first so I haven't been able to work on it for a couple of months here, but the other day I cleared up my schedule, and ran into an issue. I rebuilt the top end of the motor, replacing piston rings and gaskets...

I need 2 cable tension adjusters for my CL350 build. What they're off of doesn't matter at this point, I just want her on the road before summer is over. The cables on the bike are 8mm so as long as the adjusters are the same size, I don't really care what they've come off of, I can make them...

Hi all, missing an obsolete part, can't find it anywhere on the internet even. Can't finish my build until I can get my hands on a clutch adjuster screw. CL350k3, Honda part number 22837286010. Please let me know if you have one or know where to find one. Located in metro Detroit.

Hi all, I'm in need of a few small parts to get my bike on the road after a long build. I need a Blinker relay and a clutch adjuster cam. If you are interested in any trades, take a look at the buying forum, I'll be listing a bunch of parts I have extras of or have gone to aftermarket with.

Hello everyone, I've had a lot of great help from the community so far, hoping for a little bit more here. I'm going to flip my gauge mount to avoid the "frog eyes", but it's hitting the top triple tree without modification. In the future I'll be upgrading to smaller gauges but until then I'm...

I have almost completed my build of my '71 CL350K3, and am just hammering out controls, electrical and exhaust, and am getting ready to put my carbs together after rebuilding. The issue I am having is there is a small amount of bowing between the float bowls and carb bodies. I have the correct...

I need new slow and pilot jets as mine are pretty tore up, I found a NOS keyster kit on eBay, but I want to make sure the part number is correct since in the picture (Part # 7300-317), it looks like the ones in the picture are threaded, and the ones I've pulled out of my carbs (one is a 3d and...

Hello All, I've got my bike more or less all put back together after a complete stripdown and cleaning/repainting. I'm getting ready to put the tank and carbs back on but after taking the carbs apart, it looks like they need to be rejetted as the O-rings are almost non-existent. The main thing...

I bought a pair of Emgo shorty mufflers for my cafe build, and after cutting the headers off the OD of the header is close to the I'D of the muffler, but I want to make sure I've got no leaks. Is there a compound I can use to fill in the gaps? I'm planning on slashing the end of the muffler and...

I'm currently putting my rear wheel back together and it's time to put it on the frame the problem I'm having is there are two collars that go on the rear axle that are only about a centimeter difference in which I don't know which one goes on which side and exploded views don't have them side...

Hi everyone, my first bike has been stripped down, painted and engine rebuilt, exhaust chopped and wrapped, and now I'm looking at the electrical system. I have a CL350K3 that has the stock controls, but they are in dozens of pieces in bags. I'm assuming that they are complete, but it would be...

Hi all, I bought my first bike (CL350K3) as a basket case and was shorted a number of parts. One of those was the rear shocks. The guy gave me a pair but they were for some other bike. Then he realized he had given me the wrong ones and shipped me what he though was the right pair.... nope...

Hi everyone, I've been slowly building my first bike from a basket case I bought mid-last summer. I've rebuilt the engine, painted the frame, and am getting ready to put everything back together so I can ride her as soon as the snow melts (if that ever happens) here in metro Detroit. I have new...

Hi all, I bought a 1971 CL350 K3 for my first bike as a basket case, and learned my lesson the hard way about buying a non running bike. In any case, I'm looking for a few parts to get her running. I've sent a message to a family friend to see if he has parts, but I want this bike running as...

Hello all, I'm a first time builder working with my first bike, and have had multiple issues I've been able to resolve by myself (broken off spark plug, needed a helicoil, broken piston ring, screwed up timing etc) but I've got another issue that I'm hoping I can overlook. I lapped the valves...

Looking for a set of clubman bars, from the sound of it many people around here dislike them, so send me the ones you took of to put on your clip ons! I'll pay shipping but I'm not looking to spend any more than $25 since they're 40 new from DCC. Let me know the drop on em or send me a link via...

Bought these on eBay, they sent the wrong ones and told me not to bother returning them, then refunded me. I can't use em. Just pay shipping + whatever the PayPal surcharge is. Or send me a check, or if you're in the Detroit area come get em...

Can anyone tell me what size the bearings are for a CL350 triple tree? I'd rather buy new ones, and old ones are running about $25 on eBay.

Hi all, I'm a college student building my first bike, and looking for a little advice. My frame is gonna be rattle can black (if I could afford powder coating I would. I can't). But I will be painting my tank with quality paint. I have a paint gun, but my question is this: what brands of paint...