Search results

I need a '76 clutch lifter plate for my CB750. Please send me a PM or contact me at: craig underscore barlow at sympatico dot CA Cheers

Thanks in advance for reading. Looking for tire suggestions to fit onto my stock '76 cb750 rims. Wanting to go for the tracker look, want something safe, bike will be mostly on the street - odd time gravel roads. Was looking at these: Kenda K761 . . . . anyone try these? Anyone run the...

Hi, thanks in advance for reading.....just about to button up my crank cases ('76 Honda CB750) - my first bike, my first build, my first engine tear down and rebuild. I REALLY do not want to have to open it all back up after all the hard work I've put into it. I did a "dry run" and put the...

Hey, thanks for reading. I'm just about to put my '76 CB750 engine back together (after a much longer than I thought teardown and cleanup :o) with new gaskets, seals and hardware. Do you have any last bits of information for me? IE. "make sure to spray the head gasket with copper seal"...

Mine is sheered off. Need part 30231-300-010 #8http://www.cmsnl.com/honda-cb750k6-four-canada_model14381/partslist/E07.html#results in diagram Please PM me if you have one. Cheers

Looking for the lengths of the mounting bolts for my '76 CB 750. The PO had all sorts of mismatched bolts, nuts and washers. Some were much longer than they should be. All help would be appreciated - can't seem to find the lengths anywhere. Cheers.

'76 CB 750 in need of an advancer shaft #8 in the schematic PRODUCT NUMBER: 30231300010 Send me a PM or email me at: craig(underscore)barlow(at)sympatico(dot)ca cheers

Bike: '76 CB750 - two issues (presently :o) 1.) Taking out the crankshaft the other day I noticed the advancer shaft was slightly bent (before taking it all out)….hit the side of the case on the way out and SNAP. >:( F*ck! Check out the duct tape that the PO had put on it. Must have...

Thanks for reading and any help would be much appreciated. Engine: '76 Honda CB750 Problem: oil seals stuck, corroded How do I get these out without tearing up the aluminium? I've tried soaking in brake & carb cleaner, heating, etc. Can't get the buggers out. I got most of it out, but...

It's been awhile since I've been on the forum….new baby, new job, crazy at home, yadda, yadda. Finally got a chance to start working on the engine: '76 Honda CB750. This is my first tear down and am a noob to all of this. Just got my bike license this past summer. So, got the motor taken...

Hey, thanks for reading . . . I have a '76 Honda CB750 in a '73 frame. It's my first bike and this is a learning experience to say the least. Wanted to get an idea and your advice on how to proceed next. I've had it since July this year, have not had it on the road (just put it into my...

Am looking for more detailed info than what's provided in the manuals that I have for carburetors, ignition, tune ups, etc. and was looking to buy some gently used Mike Ross manuals http://www.motorcycleproject.com/motorcycle/text/booknook.html#13. Please shoot me a message if you have any that...

Thanks for reading . . . Going to upgrade to an electric starter and was wondering what others use, any issues with certain brands, etc. Right now I've looked at Dynatek Dyna S Ignition - DS21 system http://4into1.com/dynatek-dyna-s-ignition-system-ds1-2-honda-cb500-cb550-cb750/ and . . ...

Thanks for reading. Man, it's taking me forever to sus out this wire harness. So, I'm a noob to all of this. Get my bike, guy tells me it's a '73. I don't figure out until later, after I'm knees deep in wires and order a new harness, that the motor & switches are from a '76. Ok, ask on...

Anyone know if Honda CB bike seats are interchangeable?? Have a '73 750 which the PO put on a hideous and uncomfortable seat - would like to swap it out for a stock seat until I decide what I'd like to do with the bike. Thanks for reading and cheers!

Thanks for reading . . . just replaced the wire harness on my '73 cb750 and found that I had one plug with nothing to plug into, two wires unsure of and one with nothing to plug into. FIRST ISSUE & SECOND ISSUE: i) from new harness - one black (female) and one orange/red (male) . . . . only...

I'm a dummy. Accidentally ordered the wrong wire harness loom. Have a new loom for a '73-'75 and have a '76 engine in a '73 frame. Any way that I can make it work (modifications) or will I need to send it back and exchange? Cheers.

I disassembled my newly acquired '73 Honda CB750 front caliper as the pads were dragging. Piston was seized up - managed to dismantle and got everything out. The piston head and opposite caliper has black gunk on/in them - was this a seal that went south over the past 40 yrs or something else...

I've always wanted to ride and own a motorcycle. I grew up riding a Honda ATV that we used for hunting. Threw my leg over an old Nighthawk back in university and drove it (probably in 1st gear) around a parking lot. That's about all my experience I've had with motorcycles. At 41 I decided...