Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature currently requires accessing the site using the built-in Safari browser.
We noticed you are blocking ads. DO THE TON only works with community supporters. Most are active members of the site with small businesses. Please consider disabling your ad blocking tool and checking out the businesses that help keep our site up and free.
Well, I thought I'd put this one on the restoration section since that's where it's fitting at the moment. No plans to cafe' this one. Just bring her back from the dead and get her to a new home.
The story with this machine comes from a mix of what's on the bike now and what the previous owner...
Hello All, I recently checked in on the 1-800-CAFE-HELP board as I'm always up for helping others. Do I know it all? No, hardly, but I clean a lot of carburetors and fix a lot of old motorcycles so maybe something I've seen can help you stop that fuel from going where it shouldn't, or making...
Well, I took a project off a friend's hands and I paid far too much for it maybe. Or maybe not. Either way, he had fully disassembled the engine and had the cases blasted etc. So my dilemma is that I have cleaned up and honed, or had machined several top ends, and cylinder walls, heads...
My forks are pitted/cratered so bad I can't use them, hell nobody can! So if you have a set of fork legs for a CB500/CB550 that you are willing to part with, let me know. Thanks in advance.
Realistically the LEFT leg is the bad one, I could live with using my right one so if you only have the...
Well, I searched for getting an engine unstuck, and well...I'm stuck. :P
Here's my issue. I've got a "free" 1976 CB550 that was seized a bit...and by a bit...I mean holy crap it was in rough shape (hence free) I got all the bolts unstuck, got the top of the engine off, was able to get the...
Hey guys! I'll say thanks in advance for any insight and the best way to go about it.
I'm helping a co-worker get his 1971 SL350 back in shape. It was sitting in a barn for several years. It ran great for a while and then I heard some cam chain noise. So I decided to check the tensioner as...
Hey gents. I swapped an exhaust that fit my CB500 (since it was made for the bike) to a different setup from a Suzuki Hayabusa. I was wondering how hard it might be to make the collars, not the part that you are physically screwing them down with, but the little "spacers" that make it a tight...
Hello Gents, not sure where to post this, so I thought it might fit into bodywork section...
I'm working on a 1971 cb500. I really dig the look of benjies lower /upper fork covers. Are these only made by him? Or do other bikes have something that might fit? I generally like to make...
I suppose I'll start a thread on this poor bike I picked up. Got her for a steal, without a title, but called before I picked it up to ask about the VIN. Free and clear, title in my hand and name. Time to get to work. Cleaned out the carbs, got her running, ran her around the block and through...
Well gents, I finally got a moment to get to a 1979 DT250F that I got a while back. The problem is that I can't seem to get it to run well. I've been lurking on Yamaha Enduro forum too, I got all the wiring sorted out, but I thought I would see if anyone on here has any knowledge of these...
Ok gents...I'm at a loss, and I've never run into a clutch with this type of install before...
Background: Helping a friend of my brother in law swap out his clutch on a 1976 KZ400. He drove it over to my house, had me drive it, and the bike would only grip at the VERY end of the lever pull...
Is there an exhaust cross-reference list? I know that's one hell of a stab in the dark, but the axle diameter and fork tube diameter lists on our forum are AWESOME. Main problem is that I have a 1971 SL350 that is in need of some headers at the least, full system would be nice. I thought maybe...
Well, it's time for me to start this thread. I got this beauty for $300 last year and finally have the time to work on it now that the other bike is done and the wife is happy with it.
The cbr came to me without any plastics on the front end. It did have a seat, gauges, and the rear panels...
Hey gents. I haven't done a ton of researching but I thought I would ask you guys since I've seen quite a few people swap triples so you could have a newer or different front end on a bike. I was wondering how hard and what safety concerns there might be. For example, I've got a guy I work...
Hey guys, I responded to a kid on CL that said he needed help with his CL450. He's a younger dude that got a basket case and got in a little over his head ;) Not that we all haven't done something similar right? :-X
Anyways. He said he was having trouble with his kick starter. So I came...
Well, I've had a myriad of bikes in my life thus far, but every two-stroke I've owned, has never had any problems and I ended up selling each one before they did. So in all honesty I don't really know much about them. I've got 2 new-to-me enduros and I'd like to actually learn something about...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.