Search results

  1. CALfeRacer

    Is this Toast?

    Mega thread revival… got another project so the 350 stalled out. Trying to wrap up the engine build now and keep running in to hurdles. Machine shop said pistons were out of round and required going to +1mm, got everything back and went to assemble last night. Noticed my cam chain tensioner does...
  2. CALfeRacer

    I want to indoctrinate my friends and family...

    One of my high school teachers up in Bellingham rode a 70cc scooter (don't remember exactly what) for years without a license and never got a second look from cops. Probably not the best advice, but maybe worth getting a CT70/90 for them to try out a few times without a license, and if it...
  3. CALfeRacer

    Honda CB350P0 FAT cams 14101-297-010 NOS .************* All SOLD now

    Understood, wasn't expecting international to be cheap. I'll shoot you a message to get some more info, this still seems cheaper than getting my cam hard faced and re-ground. Thanks!
  4. CALfeRacer

    WTB CB350 Fat Cam

    Hey all, might be a longshot but I'm looking for a CB350 Fat Cam. Working on my engine rebuild and found pitting on my cam, rockers look good though. Figured I'd check to see if anybody has one before sending mine off to Web to be reground for $$$. Thanks!
  5. CALfeRacer

    Honda CB350P0 FAT cams 14101-297-010 NOS .************* All SOLD now

    How much to ship to the US? Trying to wrap up my engine rebuild and found pitting on my fat cam.
  6. CALfeRacer

    CB350 Shifter Assembly

    Yup, hard to tell on the fiche. The whole thing is a bummer because I would be fine if I didn’t lose the collar (13) through 6 moves while having the engine torn apart [emoji2369]
  7. CALfeRacer

    CB350 Shifter Assembly

    Yup, 15 has a chamfer to accept a flat head bolt on the opposite side.
  8. CALfeRacer

    CB350 Shifter Assembly

    Hello everyone. Working on putting together my CB350 engine and ran in to issues putting together the shifter. I have this collar that seems too big to fit in the fork, even though I bought the listed part number. I assume it’s supposed to fit in the fork but figured I’d check before filing it...
  9. CALfeRacer

    Post a pic of your latest purchase

    Traded the 82 900F for its 23 year newer sibling. Sad to see the 900 go but needed something better to commute with and can’t justify having the 900 as a project alongside my Toyota rust bucket that’s taking up my garage.
  10. CALfeRacer

    cheap Chinese gas tanks

    I bought one of these from 4into1 for my CB125, had to mod the rear mount to work with my rubber tank mount. The rubber pucks for the front mount on my factory tank are too big for this tank, what did you guys use? Looks like I need ~7/8" OD to fit the tank, then I'll make a couple tabs that...
  11. CALfeRacer

    CB125S "Susie" Take Two

    It runs!!! Spent a day working on it, found out the pin for the mechanical advancer for the timing managed to fall out of the cam so the advancer was free spinning, put that back in, re-set the point gap, timing, and valve timing then just kicked for hours tweaking the carb until it ran and...
  12. CALfeRacer

    CB125S "Susie" Take Two

    Merry Christmas everyone! Been working on the bike for a couple of days, made a pan to mount the battery under the seat, and started working on mounting the new tank. Rear mount is done, just need to make some front mounts to work with the Honda frame. Unfortunately my welder is back down in...
  13. CALfeRacer

    CB125S "Susie" Take Two

    Got home for Thanksgiving and since everything is locked down I got some time to work on the bike. RedKote job went to shit but did expose a couple of pinholes on the bottom of the tank. Plan is to pick up one of the ebay universal tanks and make it work. Tried starting with the "gas in a water...
  14. CALfeRacer

    NEW SITE - BRINGING OVER YOUR OLD BOOKMARKS

    No worries, I was able to find the old bookmark I was looking for by just searching on the new site. Figured it was worth asking though. Thanks!
  15. CALfeRacer

    NEW SITE - BRINGING OVER YOUR OLD BOOKMARKS

    Hi Tim, sorry to dig this up but I couldn't get that link to work. Is it possible I'm just too late and the old site is gone for good?
  16. CALfeRacer

    1982 CB750F...Better Devil

    Looks like that arches up a bit more than the braided line on my 900F, but the fitting on the caliper side of mine isn't flat so there's a bit more hose to the left of the clip on the brake stay... Hopefully that makes sense haha
  17. CALfeRacer

    1982 Honda CB900F “Holly”

    It felt fine taking it to 100+ before, but haven't gone over ~85 with the fairing on yet. Sounds like I have another excuse to ton up now! UPDATE: Briefly got up to 100 on my ride to work this morning, didn't notice any instability. Wasn't there for long though.
  18. CALfeRacer

    1982 Honda CB900F “Holly”

    Seems like the fairing is helping out with the wind, definitely taking a lot off my chest. The bottom half seems pretty secure but the top shakes quite a bit so I might need to think of a way to reinforce it. I have some random carbon strips so might buy some epoxy and glue a couple strips on...
  19. CALfeRacer

    1982 Honda CB900F “Holly”

    Didn’t like how much wind I was catching on the highway so I decided to roll the dice on an EMGO fairing. Seems like it suits the style of the bike and I’m happy with it. Once I buy an expansion tank and spray gun it’ll get painted gray to match the tank along with the “new” tail and front...
  20. CALfeRacer

    400four, Dueling Banjos

    Looks great!! Maybe I missed it, but where'd you get that cowl?
Top Bottom