Search results

  1. Uglyrabbit

    Yamaha R5C - TR3 Race Rep

    Nice project. I’m jealous
  2. Uglyrabbit

    Xs500 project

    Thank you Sent from my iPhone using DO THE TON
  3. Uglyrabbit

    Photo bucket fixer

    Anyone know if there is a fix for the iPhone? Sent from my iPhone using DO THE TON
  4. Uglyrabbit

    FZR600 Neo-Cafe

    That will look good! Sent from my iPhone using DO THE TON
  5. Uglyrabbit

    Xs500 project

    That is why I have gone through the trouble of replacing the cast 19in front wheel with the 18in spoke wheel Sent from my iPhone using DO THE TON
  6. Uglyrabbit

    Xs500 project

    Sent from my iPhone using DO THE TON
  7. Uglyrabbit

    Xs500 project

    Painted and installed Sent from my iPhone using DO THE TON
  8. Uglyrabbit

    Building my own two-stroke "Mongrel" - Inspired by CharlieT & TedT

    Re: Building my own two-stroke "Mongrel" - Inspired by CharlieT & TedT Radical! Sent from my iPhone using DO THE TON
  9. Uglyrabbit

    Xs500 project

    Mobius, I am confused by your question. My bike is a Xs500 not an RD350 so the forks are installed in the factory orientation. I know that the rim is wide I’ve made a few rookie mistakes with this bike but it is far from being complete. My intentions were to run Dunlop 100/80/18 front and...
  10. Uglyrabbit

    Xs500 project

    I wanted to clean up the triple tree because I didn’t like the now exposed clamps. So I attempted to use and XS400J flat top triple but the spacing is off by 10mm. I may revisit this in the future as it will require the use of the bottom triple clamp, a new fork brace, possibly a new axle and...
  11. Uglyrabbit

    MOPEDS MO PUSSY

    F that! Build them all! Sent from my iPhone using DO THE TON
  12. Uglyrabbit

    Re drilling spoke hole question

    Mobius, Thanks for the reply. I tried to use a countersink tool on the front rim to no avail. But after reading your post I'll have to try it again, I tried to do it without the rim laced so I'll try your method Sent from my iPhone using DO THE TON
  13. Uglyrabbit

    Re drilling spoke hole question

    After looking at a few picks of other wheels with MikesXS rims I think the problem may be the spoke length. I think the spokes are too long changing the angle at which they exit the hole. Sent from my iPhone using DO THE TON
  14. Uglyrabbit

    68 Ducati 250 SSS minus an S

    Nice! Sent from my iPhone using DO THE TON
  15. Uglyrabbit

    Re drilling spoke hole question

    Thanks I'll have to give them a call Sent from my iPhone using DO THE TON
  16. Uglyrabbit

    Re drilling spoke hole question

    The wheel Sent from my iPhone using DO THE TON
  17. Uglyrabbit

    Re drilling spoke hole question

    So I unlaced my outer spokes and sighted down the hole. It appears the hole is correctly drilled. As seen in the pic. But for some reason the nipple head is seating on only part of the rim as seen in the second pic. I don't think it is laced wrong. But I am a rookie at wheel building. Sent...
  18. Uglyrabbit

    Re drilling spoke hole question

    So I have bought myself a truing stand to true my wheels: Rd350 hubs Rd350 NOS spokes MikesXS 18x2.15in high shoulder front and rear rims I have laced the rims and got them as close to true as I can but my spokes are bending because the spoke angle is not correct. Does anyone have any nuggets...
  19. Uglyrabbit

    Post a pic of your latest purchase

    Nice bike! Sent from my iPhone using DO THE TON
  20. Uglyrabbit

    1973 Honda CB250 Twin - Australian Build

    Your bike is making me want a Honda! Sent from my iPhone using DO THE TON
Top Bottom