Search results

  1. JB77

    1972 cb/cl 100

    Glad I could help. Sent from my 831C using Tapatalk
  2. JB77

    1972 cb/cl 100

    Call Dave, http://www.davequinnmotorcycles.com he'll hook you up. Great guy to chat with and figure out the exact route to take with your bike. Sent from my 831C using Tapatalk
  3. JB77

    1972 cb/cl 100

    300mm/11.8” soft body shocks with 14kg springs. Top bush is 12mm bolt x 24mm width, bottom is 12mm bolt x 19mm width. They dropped me almost two inches from the cheap scooter shocks the P.O. had on it. Sent from my 831C using Tapatalk
  4. JB77

    1972 cb/cl 100

    You all know what a bunch of wires crammed in a headlight bowl look like. So here's the cheap switch, and a shock.
  5. JB77

    1972 cb/cl 100

    I thought that as I was writing the post Trek. I'll try to grab one tomorrow. Sent from my 831C using Tapatalk
  6. JB77

    1972 cb/cl 100

    I hadn't worked on the little 100 for a while. I have a couple updates. I ordered a set of Hagon shocks from Dave Quinn, and installed them. I checked the timing with a strobe and it checked out proper. Discovered the PO didn't wire the key and kill switch properly, so I figured that out. I just...
  7. JB77

    1972 cb/cl 100

    As per Crazy's suggestions, I took the stator cover off and checked all the wires. The neutral switch wire was pinched but operational, everything else looked good. So I went back and re static timed the little cl motor. After resting my points to where they want to be now that the cam chain is...
  8. JB77

    1972 cb/cl 100

    I did check cam timing. I had the cam cover off so I could check it before fully buttoning everything up and trying to start it. Thanks for the response. I think I might have a grounding or pinched wire issue from removing the stator. I'm going to retrace my steps this weekend and check all the...
  9. JB77

    1972 cb/cl 100

    So I realized that my issue with the cam chain tensioner was that the po, or whoever had this thing opened up before him put the wrong circle clip in, and from what I could see forgot the two 6mm washers that were needed on the adjusting screw. I drained the oil, opened her up and replaced the...
  10. JB77

    New Member, old bike problems

    Sweet! Glad it's running, I like that blue tank[emoji3]
  11. JB77

    New Member, old bike problems

    Nice!
  12. JB77

    1972 cb/cl 100

    This article is from last year but I just came across it. Pretty good read about a '71 Cl100. http://lanesplitter.jalopnik.com/how-i-rebuilt-an-extremely-sketchy-honda-cl100-scramble-1720836632
  13. JB77

    1972 cb/cl 100

    Good luck with your cl. If you read my whole thread, which can get boring at times[emoji16] , the other members have given some great info on advance, and carb tuning.
  14. JB77

    1972 SL125 motor

    Sorry to here you have to sell. Really sharp looking bike. Good luck.
  15. JB77

    1972 cb/cl 100

    Took the generator off to take a look at the cam chain tensioner adjusting screw. It was jammed down all the way, and the tensioner was loose. I was able to get it free and reset the tension. Changed the oil and buttoned it up. It ran good with less noise, and turned off with the switch. Today I...
  16. JB77

    1972 cb/cl 100

    Tried moving the cam chain. In moved one tooth in the direction needed, it put the timing mark the same distance away, but on the other side of the mark. I did find that the tensioner screw only moved a little bit back and forth when the lock nut is loosened. Should I use force to move it more...
  17. JB77

    1972 cb/cl 100

    Would the cam being one tooth off cause the bike to not shut off? I took it for a test ride, ran great through all the gears and throttle positions, just won't stop running with out rolling on the throttle after the switches are in the off position.
  18. JB77

    1972 cb/cl 100

    With the strobe, in full advance it lined up right with the two advance lines, at idle it lined up with the F. I do have the points plate way off from the manual and pics of other 100's. I had to turn the plate counter clockwise to get the timing to line up. Way advanced compared to others.
  19. JB77

    1972 cb/cl 100

    Crazyp, It has the circle. I zoomed in on the original picture, it is lined up with the indent on the head. Do you think it on a tooth off?
  20. JB77

    1972 cb/cl 100

    Put the nos advancer on, my original was definitely not functioning properly. I dropped the 110 main jet back in the carb and put the clip back in the center spot on the needle. It runs much better, I still need to fully tune the carb. The only big problem is when it is timed right with a...
Back
Top Bottom