Search results

Sorry guys closed on my first home this week and have been tied up with that. The plugs I have in now are Denso X24ES-U which from what I heard are one of the better ones to use. That's what's in right now. I also have NGK D8EA sitting around that can go in. Any thoughts? Sent from my SM-G935V...

Plugs are brand new. Forget the band off hand but there one of the better ones for this bike, I'll look and get the name tomorrow. Just polished, there was interference with the new Pistons before I got the thicker gasket so I just polished them to get rid of the very small marks the Pistons...

No its a whole new dyna S system, got rid of the points. Again I don't know why I can't get my timing strobe to work with it, it's a brand new light. It was timed as instructed with the spark fully advanced. Sent from my SM-G935V using Tapatalk

Light black. Plugs are also oily. At this point I'm hoping its just a carb/timing issue. I knew the carbs would need to be adjusted after the pods, bore and exhast. I also static timed the dyna coils but I can't get my timing light to work on this system for some reason. Sent from my SM-G935V...

I'm getting 150psi across all 4 cylinders cold. Is that enough? Sent from my SM-G935V using Tapatalk

Have my 74cb750 bored out to 811, right now I have 110 jets in the carb and getting dark exhaust. It's not every dark but certainly noticeable. The motor is bored out to 811, because of the Pistons I had to have a thicker head gasket made its .070mm thick, with pods and 4 into 1 exhaust. Too...

Would adding an o ring or copper washer help? Sent from my SM-G935V using Tapatalk

Sounds good, thank you Sent from my SM-G935V using Tapatalk

On and off less than an hour total just to check that things are working properly Sent from my SM-G935V using Tapatalk

The only thing I've done since the rebuild is turn the bike over and let it idle the bike has yet to be ridden and this is what the oil is looking like. It's bored out to 811, It doesn't smell like fuel has and doesn't seem metallic at all. Is this normal and I'm over thinking running penzoil...

I didn't see that in the instructions, I'll look again and try to find them online and download them. I'm guessing it will be one per signal. I have resistors sitting around I'll see how it looks after I figure out that setting as well as the speed setting Sent from my SM-G935V using Tapatalk

Makes sense, I'm trying to find more info some stuff I read says to add a resistor, but I can't seem to find more info. Wrapping it around the spark plug wire didn't really work, think it's to insulated to get a good reading. Sent from my SM-G935V using Tapatalk

I'm having a small amount of oil leak from the top bolt of the stator cover. Its not much but I'm confused what bad seal could be causing the leak? Sent from my SM-G935V using Tapatalk

Wired my acewell speedo up to my coil today like the instructions say. Instead of wrapping the wire around the spark plug wire, I wired it directly to the coil as is one of the options. But I'm getting what I think a tach reading of what is double my actual rpms. The acewell reads ~4000rpm while...

https://youtu.be/1HOOkJYXjG4 Sent from my SM-G935V using Tapatalk

With the old coils and points on https://youtu.be/1HOOkJYXjG4 Sent from my SM-G935V using Tapatalk

Says the advance on my bike is possibly 2500 rpm. I was going by the wrong notch on the wheel. I got it timed perfectly statically but didn't hook it up to the test light yet. I did fire it up to make sure the wiring I was messing with was all okay. It started right up but now I'm getting dark...

Trying to time the new dynatek ignition on my cb750 k4 statically. I followed the directions perfectly but I'm still having it fire before the advancer is fully advanced. I can't move the plate any further to retard the timing and I don't want to start messing with the actual pick ups too much...

Ended up sanding the domes a little bit and ordered a gasket .070 thick for now. Hopefully this will work! Sent from my SM-G935V using Tapatalk

Sent the dmv a email two days ago waiting to hear back that would be nice and easy if I can do that! Sent from my SM-G935V using Tapatalk