Search results

  1. MrMister

    75 CB200T build

    Since the Hagons are about an inch longer than stock, had some exhaust clearance issues. Promptly addressed with some bushings. Sent from my iPhone using DO THE TON
  2. MrMister

    CB378 high compression *HELP*

    Good day everyone. It's been about a year since my 378 swap, and since I did, the compression has been high. I'm about ready to pull the engine again and get even thicker gaskets from Lani to get it perfect. All i can think is that the head must have been shaved without my knowing it at some...
  3. MrMister

    75 CB200T build

    Thanks. The 200 is a fair bit more straight forward than the 350/360’s. Which is evident looking at the carbs. I never knew the smaller bike’s cylinders ran simultaneously. Sent from my iPhone using DO THE TON
  4. MrMister

    75 CB200T build

    The bike shop is crazy busy, and would have had to wait a week or possibly two. So bought some amazon special tools and away we go. Lapping is pretty straight forward. Remember to lube the valve stems when you put them back in. Also remember to mark your valves and springs. (Notice my ziplock)...
  5. MrMister

    Project Atlas - '69 CB350

    Looks good. My first build was a 71, and put your tank on. What are you planning to do with your original tank? Sent from my iPhone using DO THE TON
  6. MrMister

    tz inspired cl350

    Sent from my iPhone using DO THE TON Definitely recommend some covers (heat shields) for the pipes.
  7. MrMister

    tz inspired cl350

    Looks great. Check out my CL360 build. I put a 2 into 1 on as well. Sent from my iPhone using DO THE TON
  8. MrMister

    75 CB200T build

    Check out the og exhaust gaskets. Probably pure asbestos wrapped with copper wire. Sent from my iPhone using DO THE TON
  9. MrMister

    75 CB200T build

    While adjusting the tappets, I noticed a small amount of light leaking through the left valve’s exhaust port. So... pulled it apart and cleaned it up. I do have valve grinding/lapping compound, but my spring compressor isn’t deep enough for me to put the little stem locks back in again (had to...
  10. MrMister

    75 CB200T build

    The CB200 was way more popular in England. One of the reasons I went with Hagons. Thought I’d keep it in that tradition with a Lucas style brake light. Sent from my iPhone using DO THE TON
  11. MrMister

    75 CB200T build

    Thanks. Yeah it had some bubbles when it arrived so I had to. It’s a small bike so went with 5 fork oil which is apparently stock for gsxr600s. Sent from my iPhone using DO THE TON
  12. MrMister

    75 CB200T build

    Painted, polished and spiffed up. Polishing is honestly my least favorite part of a build. There’s just so much sanding by hand involved. But the end result is definitely worth it. 320 grit. Once you think you’re done... you’re only about 1/3 of the way. Then repeat with 600 grit. Then 1000...
  13. MrMister

    FLYSCREEN *SOLD*

    Made from poly-urethane.
  14. MrMister

    FLYSCREEN *SOLD*

    Universal flyscreen for any bike with a standard 7"(bulb diameter) round headlight. Fits headlights with 7.5"-7.75" in diameter. The headlight opening/hole is 8" across. It is about 16" tall from bottom to top. Inside mounting surface is 9" apart. $80 with free shipping. Accidentally...
  15. MrMister

    75 CB200T build

    Officially scrapping the cheap plastic seat pan, (what a surprise:rolleyes:). Ordered a seat with a metal pan from Eric at Bikeseatfactory.com Looks pretty cool on the website.
  16. MrMister

    75 CB200T build

    Slim Hagon shocks from DCC. Everything is smaller on the 200. And everyone is out of 9/16 bushings, so making some reduction sleeves. Also the stock suspension’s clevis is M8 instead of M10, so put in a thread tap and reduction bushings on there too. Sent from my iPhone using DO THE TON
  17. MrMister

    75 CB200T build

    Did a light sand before re doing the base white. Turned out alright for a rattle can job. Sent from my iPhone using DO THE TON
  18. MrMister

    75 CB200T build

    The painters said that the clear needs to be applied an hour after the base coat, so went with 2K Max.
  19. MrMister

    75 CB200T build

    $15 GSXR steering damper cleaned up and given a clear coat for good measure. Sent from my iPhone using DO THE TON
  20. MrMister

    Help identifying part.

    That makes sense, since i put an electronic ignition on. Thanks.
Top Bottom