Search results

Bike got knocked over by ass hat, need to replace my tank. Looking for a tank thatll fit a cb750k2 with knee dents. Anybody got one or a source for one?

So my bike got knocked over and im looking for a replacement (yay insurance coverage) tank with knee dents. I can find several fiberglass tanks in the style im looking for but I remember reading something about they should only be used on the track or something.... Thoughts? or a source on a...

Crank shaft and arms Tranny shift forks drum shifter arm levers Rear shocks Piston set Cafe hoop Kick starter arm (off set) Bobber kick stand & spring Rear brake actuator Start motor cover Head light bucket Carb bodies (3 various conditions) Horn (working, metal chrome, ehh surface condition)...

Ive posted all my stuff before but I decided to put everything on ebay more bites. Most things are starting at .99 cents. http://www.ebay.com/sch/ncstatecamp/m.html?item=181441643300&ssPageName=STRK%3AMESELX%3AIT&rt=nc&_trksid=p2047675.l2562 Im moving and trying to sell my extra stuff!

http://www.ebay.com/sch/ncstatecamp/m.html?item=181374857816&ssPageName=STRK%3AMESELX%3AIT&rt=nc&_trksid=p2047675.l2562 Everything from forks, head light bucket, cafe hoops, axles, oil lines, oil tanks, brake calipers, swing arms, bobber side stands, high way bars, highway pegs, speedo drive...

http://www.ebay.com/sch/ncstatecamp/m.html?item=181374857816&ssPageName=STRK%3AMESELX%3AIT&rt=nc&_trksid=p2047675.l2562 Everything from forks, head light bucket, cafe hoops, axles, oil lines, oil tanks, brake calipers, swing arms, bobber side stands, high way bars, highway pegs, speedo drive...

Ive just "finished" my lil 5000 mile jaunt around the eastern seaboard on my 750k2 and I have an oil leak. Its more then likely the pucks that go over the studs below the rockers, but while I have the engine out and the cover off what else should I change/measure/look at/service? I know the old...

Im having a bit of an issue with the front end of my 72 CB750 having a bit of the shakes, like a addict quitting cold turkey. I only get the movements between 37ish/44ish (gps speedo). Its both a shake (side to side) and a hop (up and down) New tires - Avon Roadrunners New Seals/rebuild forks...

Im having a bit of an issue with the front end of my 72 CB750 having a bit of the shakes, like a addict quitting cold turkey. I only get the movements between 37ish/44ish (gps speedo). Its both a shake (side to side) and a hop (up and down) New tires - Avon Roadrunners New Seals/rebuild forks...

I have a bunch of random bits and parts from 750k's: covers, forks, air box, front and rear fenders, fork ears, controls, electrical bits, cafe hoops, tool holder, battery box, etc. I've also got a set of forks, from I believe a 76. I also have a 750k4 rolling frame and engine. The engine on the...

I have a 1972 cb750k with a 4 to 1 exhaust (unknown brand- allows for oil filter removal, and center stand, no chrome), probably no engine upgrades (unknown PO engine, bike received as inoperable), stock air box. Current main jets are 110 (stock for 72), with 40 slow, jets found in carb when...

I have an 08 hyosung gv250. My issue is this, bike will start with a full battery, it will start 4-5 times before the battery is too drained to start it again. The bike runs fine once started, but after those start ups and the battery has been used up the starter will no longer turn over...

Finally fed up with looking for a proper petcock (after not really being able to figure out which size it was) I brought my primed tank into a bunch of stores (lowes, Ferguson's, multiple hardware stores) trying to figure what exact thread I had. Turns out with my measurements the tank fit 3...

Finally fed up with looking for a proper petcock (after not really being able to figure out which size it was) I brought my primed tank into a bunch of stores (lowes, Ferguson's, multiple hardware stores) trying to figure what exact thread I had. Turns out with my measurements the tank fit 3...

Im almost done with my build (cb750k2) and the last thing I need is a speedo/tach. I would like a combination unit if possible (one unit). Speedo: cable driven (preferred) or gps, speedo ratio 2240:60. Tach: engine or electrical, with redline around 8 to 9, tach ratio 4:1. Built in dummy lights...

So I just finished syncing my carb (runs great!) and I got to use my regular tank for a first ever test ride. Turns out the one I bought a long time ago doesn't fit. What I need to know is how to figure out what size petcock I need. I measured the diameter, between 18mm and 19mm with a 1.5mm...

I'm putting together a resto mod bike that was never fully assembled. I'm attempting to put on the exhaust and it seems the spigot pipe (part of the exhaust is to long. I have removed the old crush washer. Can I cut it to match a regular spigot length? I ask bc it seems these and the spigot has...

I'm putting together a resto mod bike that was never fully assembled. I'm attempting to put on the exhaust and it seems the spigot pipe (part of the exhaust is to long. I have removed the old crush washer. Can I cut it to match a regular spigot length? I ask bc it seems these and the spigot has...

first off Im not the greatest with electrical but I will be having a buddy who is helping me and knows his stuff but isnt always avaliale. I am about to start buildling a wiring harness for my 750k2. I have 3 honda harnesses (unknown years), 2 fully wrapped and 1 that is stripped to individual...

Taking out my motor (Hyosung gv250) and the wire and boot are no longer connected. Looking online to buy a new ignition coil the pictures show it without a boot. Anybody know how these would connect?