Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature currently requires accessing the site using the built-in Safari browser.
We noticed you are blocking ads. DO THE TON only works with community supporters. Most are active members of the site with small businesses. Please consider disabling your ad blocking tool and checking out the businesses that help keep our site up and free.
Here's my setup
CB450 71 with Dyna coil, Dyna s ignition unit, 7amp ups gel battery, Brand new rectifier for Oregon, stock regulator.
Problem: after riding for a while one cylinder seems to cut out (I could see tach cutting out which is linked to the right coil)
So ive decided to swap the...
I have 2 carburators for sale for kawasaki s2.
Carburators are cleaned in an ultrasonic cleaner. might need a gasket kit.
80$ each plus shipping.
I can bead blast them for 10$ each.
Let me know if you guys are interested.
carbsonic@gmail.com
Hi Guys, I don't know if I'm allowed to post this here but if not please let me know admin.
I'm starting to do more and more caburator cleaning. So I'm buying a big ultrasonic cleaner to fit the needs.
Here's what I can off the members DTT:
I'm located in canada, quebec.
I have a 500mm x...
Ok,
Just so you know if I miss something please TELL ME.
My goal here is to build a rather cheap ultrasonic cleaner with super power AND big capacité.
I already have a quote for a 20L that has a heater 8X 50watt transducer for a total of 400w of cleaning power + heating included size of...
Here's the deal.
I'm planing to make a trip to USA next week.
I want to treat myself to a nice new ultrasonic cleaner.
Why? To clean some nuts and bolts, maybe rent it or do some carb cleaning on the side, clean spark plugs an reused fouled iridium. Make its more a gadget that a real tool for...
I've replaced my headlight for an hid one in which I can't store all the wiring... So now I have a bunch of wire hanging on the side of my tank...
I need some idea to store it and make it pretty again.
OK last year it wasn't doing this.
Since then I've desasamble the front end and change the oil on fork.
Today I removed it again because I had a loose bearing. Tight it and I've check everything. When I ride I feel like I have to correct the direction every seconds and its kind of hard to...
Hey guys,
I tought I would share that with you. New type of wifi router with screen.
AC wifi,
8" screen,
media center for music and film
Home automation!
A lot of potentials!
I've funded them and can't wait to receive it!
http://goo.gl/Whzk4r
Low on is charging,
No light no charge
High, no charge.
I know these a bypass that I can do to short the white and yellow together to make it charger harder. But I need to fix this first...
The system is charging, just not with off and high setting.
Carb might need tuning.
When Im runing down the street at 50kph when cold, its fine.
When its hot around 15-20 min later its start to hesitate when runing low throttle.
I know low throttle are slow jet. Even when hot?
Also does its sound lean or rich?
I'll recheck the carb sync and the timing.
pilot jet is clean
everything is clean.
Just ajusted the float level to stock 24mm whas a little high.
22.5 PJ
Im thinking that I need to close the air screw a little more.
Problem:
Dosn't wanna start without choke. Dies a few seconds later if I remove it and let it idle.
What do you guys...
I've done a rebuild a few week ago. Now I have a few issues to fix. One if them is the following.
The engine wasn't running nice at all. Remove the carb bowl and clean up the Jets. That's it!
After putting everything back together, the carb are pissing from the overflow. Remove everything...
Hi,
I need to know the stock height from the cast surface of the head to the mating surface of the gasket.
Does anyone have a stock head laying around?
I've had my head and deck milled. I've checked the piston clearance and all should be fine.
Timing is ok
200psi on each cylinders.
Valve are at 0.03mm
Those are high compression thr piston.
I might have mischecked the piston to valve clearance but as far as I know it was at 0.06
What so...
Hi I bought some 10th riser for my hagon on my cb450.
But I found a problem on my drive chain... It almost rub on the swing arm...
So is the stock setup of a cb450 drive chain has a roller of some kind?
If not what type would fit that model?
Thanks.
Hi guys.
I don't know if you know the website kickstarter? It's to help Compagnie getting funded to launch a product.
Check this out. I've pledge on it and what to share this awesome project with you.
https://www.kickstarter.com/projects/hellobragi/the-dash-wireless-smart-in-ear-headphones/
Hi guys,
I'M calling all the guys that did the torsion bar mod (Grind one tooth off) to get them tighter.
I'm looking for a long term reliability test and cam wear test.
Let me hear ya!
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.