Search results

I'm looking for a Top Fork Bridge for a 1973 Honda CB 350G. If you have one ping we with details, and cost. Thanks.

I picked up a 73 350G last year. The previous owner had something go bad with the starter switch, and they remedied it with a trip to the local RadioShack. I picked up a used set of controls from ebay, but they appear to be a couple of wires short. Coming out of the bucket I have a couple of...

I recently re-painted my tank using spray bombs mixed at Napa, and I finished with Spray Max 2k clear coat. It looked fine for about a week, but then a couple of bubble spots appeared. One is near the front weld points of the tank, so it isn't very noticeable, and I don't care. The other is of...

I'm looking for a points cover with screws, and a float bowl for a 73 CB 350. I believe the points cover is the same for the all years of the CB350 and covers for the CL350, SL350, and the CB250 will also fit...

I recently picked up a 1973 Honda CB350G. I've pulled the carbs, and after cleaning them, I've discovered a few small holes in one of the float bowls. Can this be fixed? If it can be, what is the best method? Solder, JB Weld, or just purchase a new one? I of course have four CB350 carbs sitting...

I've nearly finished my 68 CB 350 build http://www.dotheton.com/forum/index.php?topic=51409.0. The last major issue is the battery isn't charging. I've gone through this sticky (http://www.dotheton.com/forum/index.php?topic=48646.0) on troubleshooting charging systems, and according to this I...

I'm finishing up getting my tank back together. The final step is mounting the badges. A couple of the mounts which look like rivets fell out when I removed the badges. Short of buying a rivet gun and adding rivets, are there any other tricks to mounting badges? The badges don't seem to conform...

I've been looking for some replacement carburetor / air box replacement clamps for my 68 CB 350 without much luck. What I have found tend to run in the price range of $10 a piece. Are there any other options after market etc that will work in their place? I've heard that standard hose clamps are...

I have a couple of original air boxes from my 1968 CB 350 that I plan on using in my final build. The filter material and rubber boots are in decent shape (I think), but the rubber boots are loose. The old (what appears to be) rubber cement is all dried up. Should I use something like silicone...

I'm in the final stages of hooking up all of the wiring on my 68 CB 350. Most of this bike was in a box when I purchased it several years ago, so unfortunately I wasn't able to document the tear-down for reference. The tachometer has two green wires, which I assume are grounds that have me...

My fiancee has a free subscription to Rolling Stone. She spotted this snippet.

I'm getting close to piecing together my '68 Honda 350. The last major purchase I need to make is mufflers and I'm looking for suggestions. I'm mainly looking for something that isn't too loud. I used shorties on my last project, and they left your ears ringing. As far as style, I'm looking for...

I've been looking for a replacement fuel tank for my '68 CB 350, but haven't had much luck. Mostly everything that comes up on ebay is rusted out, or it looks like someone took a baseball bat to it. I'm from the Northeast and salvage yards are few and far between. I've seen a lot of postings...

Title says it all. I'm looking for a foot peg bar for a 1968 CB 350. I believe other years will fit as well, though I'm not 100% sure of that. I assume that since so many of these have been turned into cafe projects, that many of them have been traded in for rear sets, and are sitting on...

I'm going to dive into using two stage paints, with an actual sprayer and compressor set up. I've done research as far as time between coats, technique, etc. It all looks pretty straight forward. But as far as purchasing primer, paint and clear coat, I have no idea where to start. I don't want...

I'm getting ready to paint the tank on my 1968 Honda CB 350 and I want to remove the tank badges. Are they just attached with adhesive, or are they snapped on somehow?

I recently started on my second project, a 1968 Cb350, and this time around I've decided to make the jump from rattle cans to two stage paint. My original plan was to purchase an HVLP paint gun, but through my research, I've discovered that my compressor will not handle the air pressure/volume...

I picked up a basket case '68 CB 350 a couple of years ago, and I'm finally getting around to working on it. I purchased two project bikes around the same time just because they were so cheap, I couldn't pass them by. You can see the other here -...

If you're from the New England area, you may want to check out this show and swap meet this Sunday 9/23. http://www.facebook.com/VBMotorcycleShow?ref=stream

I'm looking for a brake pedal and peg mount bar for a 72 CB175. I'll pay cash, but I also have some CB360 parts for trade (head and carbs).