Search results

If anyone is in the market, or not.... haha I have 6 bikes already or else I'd get it. https://rochester.craigslist.org/mcy/d/1976-yamaha-rd400/6626914299.html

Moved to Middle GA about a year ago. Being in the middle of the state reminds me of being a middle child growing up.. it sucks! I did a search for members in the area and most of the posts are from 2010-2012. Are you guys still out here? Active? Have a 1973 Norton Commando 850 that needs a...

Hey guys, Moving down to Biloxi in about 1.5 months. Who lives down in that area? Any good shops for working on old Hondas? I'm planning on bringing my 73 350F down with me in a 85% complete state. It will need some work to finish it up. Since I will have limited tools and virtually no shop...

Hey guys, I have read many many articles, watched many YouTube videos, studied rim patterns, and took many pictures of my wheel before I took it apart, but putting it back together has risen some questions. Side Info: I checked the spoke lengths and angles and they are exactly the same as...

Whats up guys and gals? I am looking for someone who can make me tank decals for my 1973 350f. I like the look of the stripes that came with the tank originally, but I want both of them to be grey or silver instead of the original white and orange. I can get some dimensions if someone is...

Finishing up my fiberglass seat pan. At the stage where I start to slim it down some. I'm curious to know how much of a gap between the edge of the pan and edge of the seat I need to leave. I've seem people leaving as much as about 1/4 inch (see image attached). I imagine it depends on...

Morning, Stumbled upon a 1971 Yamaha RD200 last night on craigslist. Emailed the guy and turns out he still has it. Its rough and needs a lot of work. Ad says it hasnt been registered in 30 years. My question to you is how much work would this take to get this thing rippin once again as far as...

Looking for the ignition mount that goes under the tank for a 350f. I'm pretty sure it shares a mounting plate with the horn on the frame. I like the way it mounts and it would be easier to get a stock one than fab one up. Lemme know if you have one. See pics. Thanks

Looking to buy a cm400 tank in good condition. I don't care about paint. It just needs to be dent free and inside not to be terribly rusted. My sister dumped her bike and slammed the handlebars into her tank and dented it. Also dealing with a crack that someone tried to jb weld with limited...

Hello, I am looking to swap my 350f motor out with a 400f motor for extra GO and an additional gear. What is the average price of a 400f motor? I understand that there are a lot of variable that can increase or decrease the price. I do not know if the motor runs or what kinda work it needs. The...

Anyone? There is a small group of guys into vintage bikes. We meet on Mondays. Lemme know if you are in the area and wanna ride.

Took apart my rear shocks using the threaded rock method found in the $50 mod thread. I compressed the piston and it didn't spring back or provide any resistance at all. I'm not an expert on shocks. Correct me if I'm wrong, the piston and shock should work together as one unit to provide...

Hello All, I am looking to buy a front fender bracket from a Honda 350f. Basically, I already have a fender that I plan on using, but I need the bracket to mount it to the bike. If you have a fender with the bracket, I ask that you drill out the rivetts and send only the bracket. This will...

What's up guys? Wrapping up my café project and getting ready to fire it up soon. I've read a lot on tuning the 350f's and some say it's damn near impossible with pod filters. I originally wanted to run a single oval filter off the stock air box (the first section - oval shaped plastic bit that...

To avoid any complications with tuning/jetting, I want to run the stock air box and a 3 inch oval filter. Trouble is, I cannot find a filter anywhere. Anyone have any other ideas? Also, I misplaced the boot that attaches to the air box. So, if you have one laying around I would be interested. I...

What's up fellers? Went to a vintage swap meet/show last weekend in Rhinbeck, NY. Never been to this show before. If you are ever in the area, you should check it out! Anyways, I was about to head home when I stopped through the last isle of the swap. Sitting there in a box was along pair of...

Just purchased the GoPro chest mount, aka the "chesty". Does anyone have any experience with this type of mount for the GoPro? How about any other suggestions for mounting the GoPro to a motorcycle? I mounted it on my dad's Norton a few days ago with the suction cup on the top of the tank. The...

So, what's the deal with everyone posting pictures of a half naked chicks for their avatars these days.. I guess my Adolf Hitler avatar wont cut it anymore, huh? :)

So, when I stripped my tank I removed the badges. The little spacer that holds the badge pins fell out and was lost. Now, the holes in the tank that are designed to hold the badge are too large and the badge does not stay attached to the tank. What do I do now? Can you buy little inserts that go...

So I bought the florist foam to make my seat last year and finally got around to making something happen with it. After reading many threads on how to make seats and asking around I figured I'd try a go at it. Now, this is not the prettiest seat in the world. It is my first time and I have...