Search results

Original coils and brackets off of my CB360. I never ran the bike with them but they test out good. All of the original terminals are in tact, but the spark plug caps have been removed. Here are the test results: Primary resistance = ~4-5 ohms, Secondary resistance = ~9.5- 9.9 K ohms $55...

I've decided to get rid of some of my cafe parts to fund other projects. All of these parts are off of my CB360. Custom Made Rearsets: Everything you need to bolt right up to your CB360. Complete shift side rearset with linkage and shift arm. Complete brake side rearset and linkage (you...

Hey, I've been keeping my eye out for a cheap old fuel tank. Looking for something off of an old enduro or moto bike. Steel and slim are about the only requirements. Doesn't have to be in particularly good shape, but I am looking for something usable. Thanks.

Please see.. http://www.dotheton.com/forum/index.php?topic=21538.new#new

Hey guys. I'm looking for the rear brake rod for the cb/cl360. I don't need the spring, nut, or little drum. If you have just an extra rod laying around, please let me know. Thanks.

I'm selling my two piece Hein Gericke FirstGear leathers. They are in excellent condition and are excellent quality. Jacket: -Size 42. I am about 5'11" 165 lbs. and it fit's me perfectly. -Separate foam and solid arm/elbow padding. You can remove the solid cups and ride with just the...

Anybody go down to The Good Guys car show in Nashville last weekend? It was my first time there. Being from the Motor City, you get spoiled when it comes to car shows and hot rods. It was no Woodward Ave, but it was probably the best car show I've been to otherwise. My old digi-cam battery...

I'm planning on running an OEM CR style kill switch on my cb360. It's just a momentary kill switch that they run on the dirt bikes. The CR style switch basically has two leads, one of which is grounded to the handlebars, and is closes the circuit to ground momentarily. I know the cb's...

Does anybody have a good method for removing the float valve seat out of the carb? My carbs were horrific when I got the bike. I put a lot of work into cleaning them and they came out pretty decent. I'm still going to be rebuilding them. When I get my jet kits in, I do want to replace the...

Just though I'd throw it out here. I have a set of Dyna 3ohm green coils that I'm looking to swap for a pair of Dyna 5ohm black coils. Mine work great, so I'm looking for the same in return, obviously. Keep all your hardware and plug wires, I just want to swap the coils. If you're looking...

I ran into something assembling my engine that raised a concern. Is the spark advancer suppose to be able to rotate on the cam shaft when the bolt is out? Mine is solid as a rock on there. I didn't think anything of it when I pulled it apart, just because I wasn't sure it's function. As I...

My question is about the lug on the big counter shaft oil seal. As soon as I pulled it out, I realized I didn't see where the lug was seated. In the shop manual it says "Properly fit the lug of the oil seal into the hole in the upper crankcase." There are two places where it can fit...

Hey, I have a question for the engine guys out there... I tore my engine down this past weekend and I'm trying to decide what to do with my top end. Also, I relocated to another state recently and I'm shopping around for a good machine shop at the moment. So, I would like to get some opinions...

I pulled my tension slipper out last night just to check the condition. That was the first time I've cracked this motor open. I was just wondering what some of you do to reinstall the tension slipper? I see there is a special tool called the "push rod tool" that apparently threads into the...

Hey, I scored this helmet at the local consignment shop a couple of weeks ago and had to share it with SOMEONE. Bell R/T Wanna know what I paid for it? $4.50! I'm stoked. I showed it to a couple of guys from work and they gave me the weirdest look. I guess these old helmets just...

Finally got around to leaving some feedback on my purchase from JustinLonghorn. I know he had a few things for sale, so I wanted anyone that's considering buying from him know that he is GREAT seller. He hooked me up with a set of upper tripple trees for my 360. I must have had those...

I started my rearsets last night. Check it out over at my build thread. Once there done, I'll post the rearset specific project over here. http://www.dotheton.com/forum/index.php?topic=21538.msg230401#msg230401

I have the classic seized caliper on my 360. I've done my research on getting these things out and plan on finding the 10mm X 1.25 pitch zerk fitting and a grease gun this afternoon when I head into the city. I've tried pushing the piston back in, to break it free, but I think it's bottomed...

I've used this website for a great resource over the last couple of months as I've done research for my first build. Now that I've got a lot of things worked out on paper, I would like to share my build with the rest of you and hopefully return some of the insight I've taken from here. This...