Search results

  1. ex119x

    Hello

    There is a lot of fun and noise to be had with a 125 2 stroke street bike, without breaking the law, too much.
  2. ex119x

    Honda CA77 Dream Touring Cafe Racer

    That is the essence of the whole thing! If you are happy with it then nothing else really matters.
  3. ex119x

    ** PICS OF MEMBERS RIDES ** - Official Before & After Thread

    It looks way better than original. Nice job. Personally, there are a few more changes I would consider. I would see how some reverse cone megaphones would look instead of the stock mufflers. I think the rear fender is too big and valanced now that you fixed the front one and I would put a set of...
  4. ex119x

    1973 RD350

    90% of all jetting issues are ignition.
  5. ex119x

    1973 RD350

    It is either rich or lean and leaning it out didn't make it better, so I would suggest going the other way, but only one jet at a time. I always start with the mainland then fine tune from there. If it were me, I'd try a set of 180 mains and see if it improves.
  6. ex119x

    CB350 1971 Engine rebuild (white smoke out of breather pipe -> Obliterated head gasket)

    I have never seen a cb350 head gasket blown that badly. I have reused plenty of 350 head gaskets on racebike when I have been in a hurry. I have never had a head gasket failure. I suspect from looking at this failure that either the center studs were not torqued properly or the head and cylinder...
  7. ex119x

    Honda FT500(ish) tracker!

    With the wiseco 12.5:1 piston, I always just put it in 2nd gear and back it up to just after TDC. When it stops you are in the right place.That is way easier than trying to bump it just past with the kickstarter.
  8. ex119x

    Honda FT500(ish) tracker!

    It looks like the electric start has also been removed. The starter drive mechanism is not the best engineered part of the bike and if parts break they can be difficult and expensive to source. The FT also requires a much larger battery for the electric starter and that precludes the open...
  9. ex119x

    Honda 1975 cb400f blowing main fuse

    Just working from memory here, but I believe the starter wire is blue with a white tracer. Unplug that from the starter solenoid and check it for a short to ground with an ohm meter. If it is bad, disconnect the handlebar switch from the main harness and check again, to isolate where there is a...
  10. ex119x

    1977 Honda CB750F Build Log

    Nice job on your bike. I might have done some things a bit differently, but it might just make it different rather than better. I prefer to have fenders on my bikes, I like center mounted tail lights and license plates and I think I would have gone with a 110 x 17 front tire instead of the 120...
  11. ex119x

    ‘78 Kz1000 w/RC Turbo Kit

    I wonder if the second vent on the valve cover was intended for the oil return from the turbo?
  12. ex119x

    Valvula automatica de combustible en la CB750K del 82

    Yo creo que sI en Los Estados Unidas El 1982 CB750 no hay una valvula automatico es una valvula manual y no es asequible. Neccesitas a reemplazar con una nueva valvula manual de uno otro Honda.
  13. ex119x

    Valvula automatica de combustible en la CB750K del 82

    En Ingles, este parte es un air cut off valve. Son en e-bay en Los Estados Unitos. A donde usted?
  14. ex119x

    The Norda

    I could build something just like this. If I had more skill, patience and vision. Other than that I could probably do it.
  15. ex119x

    Honda CB-1 Concept

    Nice project. Just an FYI, if you need easy rear gearing, the Suzuki GS500F rear sprockets are 520 and the same bolt pattern as the VF500F rear cush drive. Certainly useful to check gearing and such before spending on the much nicer rear sprocket you are running.
  16. ex119x

    1972 Honda CL450 Scrambler Refurb

    Given your fabrication skills and the fact that it is a scrambler style, have you considered a small rear fender with a tasteful rack? You could then mount the tool roll to the end of the rack, resting on the rear fender above a tail light. That might look cool.
  17. ex119x

    '99 SV650 track rebuild

    looks great. No such thing as too much front brake!
  18. ex119x

    Foggy-Brain Dilemma: Pairing VFR800 Front Wheel with ZX10R USD Forks (CB900F Project) - too crazy?

    It looks like a 2008 or so CBR1000RR has 320mm discs with 5mm offset and a 94mm center diameter. It might not be too difficult to make a 5mm thick spacer with the correct ID for the vfr wheel and a 94mm lip to center the disc. That should then all bolt up. Double check the year CBR since some of...
  19. ex119x

    The Norda

    I know this may sound like sacrilege or even heresy, but is it possible or even a consideration to look at making a longer swingarm and mounting it much closer to the rear of the engine in those big rear motor mount plates. I think about the advantagees to a longer swingarm, closer distance...
  20. ex119x

    Foggy-Brain Dilemma: Pairing VFR800 Front Wheel with ZX10R USD Forks (CB900F Project) - too crazy?

    So, doing a little more internet searching, I found some numbers. Use at your own discretion, since it is internet info. It appears that the 2013 ZX 10 has 132mm disc spacing, inside face to inside face. That is the target to hit with a Honda wheel. It appears that a 2009 CBR600RR wheel has 132...
Back
Top Bottom