Search results

Painted, but with some rust. The pipe silencers are chrome. Going to try on my own once I get back my pressure washer. There was one place that does chemical baths to restore old cars/industrial parts, and they've quoted me a minimum of $200 for the pipes. Too much $$..

Thanks! I'm going to go in this order to clean my pipes.... from zero cost to $$.. - pressure washer - plug one end and shake like mad - submerge in CLR, over cleaner, or rust remover for a few days - pressure washer - take one of those toilet brushes and attach a wire to it, shove it in...

haha lol... ;D Thanks for the tip.. I go check out Now! i mean Chuck who has a strip tank... lol :)

I have a set of pipes, or expansion chambers for the 2 stroke guys.. they need some good cleaning. Besides taking a torch or putting in under a BBQ, is there a professional way of cleaning these pipes? Cleaners who use caustic materials for cleaning radiators, water tanks, etc.. ?? Anyone...

You guys are killing me! ;D I have a running bike and wanted to make mods, and a bunch of you say go get a project bike. Now I have a project bike that was dirt cheap, but now you suggest having a running bike. ARGG!! I think i'll invest about 2-3months of my time on the project...

Thanks Bradj. I'm not familiar with all the bike setups either. I don't have go with spokes. I actually like the RD400 rims. Maybe it's more economical if I find a rd400 project bike and do an engine swap.

Over the next few weeks I'll provide an update on my tear down. The forks are rusted and you're right I may need need springs. I will test them to see if they can hold my weight under stress. I wouldn't mind trading for newer RIMS (with discs back and front). I don't know about any...

The forks are straight, but I haven't pulled it apart to see if they are seized/too rusted. The rear shocks, with some TLC and rust remover can be potentially be reused ?? My other stock bike has parts that is 37 years old, and I don't think they are more or less reliable than anything that I...

Thanks Teazer! I haven't priced it up yet. I'm afraid of what I'll see. I have a running bike already, and this is just a side project for me to build the bike I deserve, not the bike I want (or whatever that saying goes) :) Thanks for the tips, I'll take into consideration everything to...

Looking for parts for my cafe racer project. I will be spending the next few months rebuilding the engine and cleaning things up, but I will need lots of parts. My goal is to complete the project 1 year from now on a bargain basement budget. There are more parts than I can list or am aware...

Somebody didn't pay their hosting fees.... !! http://www.2strokeworld.com/cgi-sys/suspendedpage.cgi

Thanks! I am going to attempt the rebuild myself. The engine kicks over and just did a compression test myself. Scored 95-100 right/left. A bit low as I think the spec calls for 100+. I will pull it apart to see what needs replacing. -K

Thanks for the feedback! These two phrases are a bit contradictory, but I think I understand. I have the Haynes manual and access to other forums like this that provides a lot of guidance. Thank you. I was quoted about $600 for a top-end rebuild. I am hoping that I don't have to replace...

I was thinking of rebuilding it myself, but im may f*ck it up. Since it currently doesn't run I don't even know the compression numbers. I want a rebuild - test compression see if I need the new pistons. New seals, gaskets and replace any worn parts at a minimum. I'm in the GTA.

First one which I will try to keep in stock form. Runs, but needs some tuning. 1975 Yamaha RD350. Second one is in rough shape. This will be my platform to build a cafe racer. Does anyone know of a mechanic who is familiar with 2 strokes and can rebuild the engine ? 1973 RD350

I'm getting the tank but no cap or peacock. It wasn't cheap. Do you know where I can get a cap for $60? I found a source, but the price is a lot higher. I wanted a pic to verify what the cap looks like. The pic I have it looks like a simple screw-on cap. Thinking there must be something...

What does an original Benelli Mojave 260/360 Gas Cap look like, and what are they worth these days, if in NOS condition? Is it worth getting an original cap, or would a modern substitute part be a better option? thanks! -K

I'm swinging by Chicago for a few days next week. Wondering if anyone had any spare parts that would work with my RD350 project. I am in need of many things, so feel free to msg/PM me with what you may have. - clip-ons, 34mm, or clubmans - rearsets - analog/electronic gauges - low-profile...

Which seat would look better on a RD350 project? I going with a Benelli Mojave tank combination. Moto Lanna or Glass from the Past - VINBTB Example of the seats on bikes... I like both for different reasons. Sorry, I didn't the the POLL option, but comments are just as good.

Looking for a seat that is similar to the following one... http://www.gftpstore.com/Vintage-seat-VINBTC-VINBTC.htm?categoryId=-1 thanks!