Search results

Time to clean shop, I want these parts out of here. If you think my price isn't fair feel free to make an offer. I'm also terrible about checking on here, so if i don't respond my email is nbraun147@gmail.com Fiberglass seat pan - 95 shipped Fiberglass fender - 70 shipped 37 mm clip ons...

Vintage Honda gurus, is this an xl350 centerport?? I know it's a terrible photo, but wasn't able to get a closer picture. I've been looking into building a bike for flat track racing and I know these are a great platform. Thanks! https://i.imgur.com/LwubhWF.jpg

Not sure if this is the best place to put this, but I do want to build something similar to a race bike, so it seems fitting. I Have a 78 gs750 titled frame that I had bought for it's engine. It sat around for awhile and i decided I would try and use some of the other parts I have to build...

Decided i'm tired of having all these parts laying around and that it's time to get ride of them. Prices are without shipping, and my location is 57006. Feel free to make an offer on something if you don't like my price. Lastly, I may not be the best about remembering to check my PM's, so you...

Looking for a set of PD Carbs for a 77-78 cb750. Looking for a set taken off a running bike or a set that were recently cleaned, so i can put them on and go. Thanks!

They're fairly rough, they're sitting on a locked up motor, and missing one float bowl. But I figured they could be used as parts or rebuilt if someone wanted to. Not really sure how much they're worth so make an offer!

I'm in need of a cb750 69-76 rear cush drive. A set of stock coils, and either a stock R/R setup, or one off of a later DOHC. Thanks!

Have a 79 gs750. The bike ran fine a year ago, but then was put to the side and forgotten about. Started back up on the project and decided to get it running again. Went through the carbs and replaced gaskets and cleaned jets. All the float heights are set right. Well #2 carb leaks a bunch out...

The contacts in my headlight switch are no longer working. I can use a jumper wire between the different contacts and get it to work, but the actual switch with the contacts will not work. Any ideas on restoring the contacts to working order? Thanks.

Hey guys i need some help trying to figure out the sewing parts of my seat. I'd like copy this seat fairly close. It appears that the whole cowl is wrapped but i don't really want to do that. Is there any walkthroughs or something like that which shows how to cut the templates and such? I...

Need some parts but don't have a whole lot of cash so thought if i could buy them used. Swapping a lifan motor onto an old moped. Looking for a universal clutch lever/perch A universal right brake lever/perch for front drum brakes universal left brake lever/perch And lastly a universal...

Need to buy some cables for the controls for a 750L but they need to be shortened as i have clips ons. Not totally sure how much shorter i should get them, and I'm not sure how to measure without the engine and carbs in the frame. Is there a standard length people usually take off when they go...

Well, as the stock bearings were basically shot on my gs750 i bought new tapered roller bearings from AllBalls. Now as this is my first time im not totally sure what to do. The lower bearing doesn't seem to go all the way to the lower triple, therefore it won't fit tight, and neither of the...

Hey, trying to find a seat similar to this, and for right around $150 bucks. http://www.motolanna.com/ourshop/prod_1910098-Seat-Cafe-Racer-v30.html Are there anyother seats similar to this? Just trying to see what's out there.

Looking for a rack of carbs for a 360. Preferably off of a running bike or recently rebuilt. The carbs we have now are just too far gone to try and save. Thanks!

I'm working on 79 gs750 and i just recently got the tire back on. The pads had closed so we had to open them, and then it was a little tough getting the caliper on, and it was a little tight, but brakes always drag slightly so i didn't think to much. The bike feels like its getting dragged, and...

Well tried to make a seat pan using fiberglass. Everything went well except i think i went a little too light on the hardener. I did something like four layers. Two layers of cut matt, and single layer of cloth, then a layer of cut peices of the cloth, then another whole layer of cloth. I layed...

Well, i finally have the bike running, and i tried to sync the carbs. I couldn't find a definative way to do it on the VM's so im trying my best. Right now on the carb tune its showing all the bars level at 18, yet, when i rev the bike it pauses, then takes off. To me this sounds like a lean...

Looking for and older kz1000 like square tail, or even the duckbill tail. Something like this.

Just a quick question here. Whenever i use the electric start the bike will just crank for a while and then pop a little bit. But when i use the kick starter it will almost always start first kick, even after sitting for over 24 hours. Any thoughts?