Search results

So.... I wasnt near the bike all winter and just got back to it. I checked the spring. It springs. Turns just a little and pops back. So I have no idea where to go from here besides the repair shop and I dont even know where that would be haha. any other ideas?

^^^^what he said^^^^ The slide fits the correct carb the right way, the wrong carb the wrong way.

Hey Guys, sorry for the lack of response on my end, its a pain getting my schedule to match my buddies who is storing the bike. SO. I got the clymer manual and have read it front to back, very enlightening though I have forgotten most of it already. I re-measure floats, they're spot on...

Idk why that's sideways...

Ok, I'll do that next time I can get to her. Here's a picture of what I'm talking about with the float height measurement being wonky, the paper jig has a 21mm cutout and the float basically bottoms out there, did I measure it wrong? 21mm is the height I'm finding everywhere.

ok, and how do you know if theyre pulling equally? i looked through the manual, hope it isnt a dumb question.

correction: subjective to a dude who doesnt know anything! Obviously objective to someone who knows....

of course 'ran fine' is subjective, but it certaintly idled in the right range and rode ok minus the brakes being garbage

Thanks for clearing that up Teazer, I'll check the advancer when I get to the points. Today I checked the carbs and installed a new throttle cable. The slides werent facing the right way, though when I changed the cable, I had put the slides back on wrong, left on the right, right on the...

Whats up with people using these firestones? Im new to motorcycles but in cycling fatter tires = less power. Is that true on motorbikes too?

So much good advice, thank you guys! Im gonna start with installing the new throttle cable, making sure the slides move freely and arent installed backwards and check the float height. I get how to set the float height and measure it now, but what should the float height be? And how to I know...

When I said top of float I meant bottom, I was thinking about how they look open and in my hands. also When i said 'flat' of the carb im talking about the gasket surface. Sorry, Im learning!

thanks for the quick response guys! The throttle cable is a little chewed and really wants to sit in an extremely dangerous place where it gets pinched by the steering lock since the clubmans sit so much lower than stock. ALL of the cables are routed like garbage actually. Ive looked for good...

So, I have a 1972 CL175 I picked up a couple of months ago and originally idled ok for the test ride and then started getting weird. I opened up the carbs and the floats were full of gas and bad solder. Ordered new floats, installed them and put the air boxes back on ( PO had them off, no...

cool, ill take a few pictures when I can get to the bike, thanks!

Hey Guys- Im looking for a 1971 CL175 right Airbox cover. Im having trouble getting her tuned and Im sure this doesnt help! Will CB175 airboxes of the same year be the same?

Oh also the PO had just installed new stock sized jets and cleaned the carbs - assuming he did an ok job but they looked clean. Just trying to eliminate possibilities...

Hey All, Ive been lurking these forums for months preparing to get my first bike since I dont know ANYTHING about motorcycles, engines or electricity. After looking at all the amazing bikes you folks build its way too easy to get extra ambitious which is just what happened when I picked up...

How similar is this bike to the CB175? Is it JUST pipes and gearing and tank? Tons of listings for OEM CB parts but not so much for CL. Previous owner was trying to run pods but he got the wrong size and looks like you need to fab a elbow to get em on. Would pods work well on this bike? Ive...

Thanks, Im stoked to ride! The bike is a little rough but not crazy it was running ok when I bought it but then couldnt maintain idle at all the next day. It ran with the choke off but not on and was revving like crazy on its own(and tach cable is broken...). The throttle cable moves freely...