Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature currently requires accessing the site using the built-in Safari browser.
We noticed you are blocking ads. DO THE TON only works with community supporters. Most are active members of the site with small businesses. Please consider disabling your ad blocking tool and checking out the businesses that help keep our site up and free.
I know some guys use WD40 to keep a bare metal tank from rusting. I've been advised (falsely, maybe?) that clear won't stick to bare metal as it needs something to "grip". That it will eventually chip, flake or lift.
Is there a method to clear coat a bare metal tank and side covers? Does it make any difference if the clear is matte or satin or gloss?
Clear powder coat would be a good option. I haven't heard much about clear flaking off bare metal. But honestly, I'd run the bare metal as is for a while and see what you're up against before worrying too much about it. Carry some steel wool or sand paper with you.
I got my bare tank powder coated and it's just like it was when I got it done 2 years ago. Only thing is that it's starting to "spider vein" rust under the clear (not bad). I assume all tanks rust a tad under paint, but if the coating is opaque you'll never know.
Only problem is that the Orange peel is pretty visible. I guess powder coating large flat surfaces will give that to you no matter what. You could always cut and buff.
If your tank is straight enough to not have to do any bodywork, I would offer up the option of polishing it. Then you could just maintain the polish instead of having to wipe WD40 on it all the time. Would look sweet. You're already sanding the thing anyway to get a nice grain.
You can also pattern it with a little sanding disc.
Many years ago I had a small micro-builder chrome-moly road bike and it was both welded and fillet brazed. The only paint on it was a small stripe on the downtube with the builder's logo. The rest of the bike was polyurethane cleared and it was positively stunning. The clear showed off everything the builder did and it was gorgeous. The clear never yellowed, chipped or discolored, and the frame never rusted.
As long as no moisture or oxygen can get to the steel, you can't grow rust. Anything that rusted under any finish wasn't properly finished or prepped in the first place. Primer is porous and can be a bad rust inhibitor, but paints and clears are not.
A good high solids clear polyurethane like PPG or Glasurit will go a long way in making a raw steel finish look awesome.
Take it to a pro auto painter and let them do it properly, and you won't regret the results.
I have never cleared over smooth (shiny) steel. I have cleared over a few bare metal tanks, but I always grind the surface with a sanding disk on an angle grinder. I believe the clear needs a "tooth" to adhere to, and the texture looks great in the sun. After sanding this tank I cleared it, then airbrushed the Marylin, cleared again, and then painted the satin scallops.
Avoid rattle can clearcoat- even 2k clearcoat, and clear powder (unless you leave low grit scratches). You need to use a product meant for adhering to polished bare metal such as por15 glisten pc or shark hide if you want it to last more than a few seasons.
Avoid rattle can clearcoat- even 2k clearcoat, and clear powder (unless you leave low grit scratches). You need to use a product meant for adhering to polished bare metal such as por15 glisten pc or shark hide if you want it to last more than a few seasons.
It's a shame all that Candy powder coating I did on chrome and other polished surfaces over the last 8 years is destined to be returned to me because it all flaked off. 8 Years, still waiting on the first part that failed to come back. Yes it is better to have a blasted profile, does it mean it WILL fail if not, certainly not.
How is that clear holding up on the side covers? I like the bare metal look but with the heat I can't see the clear holding up long at all.... Nice SR btw I'm working on and '81 exciter as well
For these covers, I cleared with engine paint. I use only 2K urethanes on tins, but I used engine paint to deal with the heat. I have seen other people use regular 2K on engine covers saying that the covers don't get very hot (at least not nearly as hot as the cylinders). There are 2K engine paints, but I don't know where to buy them locally but I know they are available online. The paint I used on these covers held up great until I sold the bike several months later. I believe the sanded texture allows the finish to adhere much better than a polished surface would. I have never cleared on a polished surface so I can not speak from experience in regards to that situation. BTW, it was a fun little bike.
Could you hook it up with a link on where to get 2k engine paint online? Got a bud who is trying to get a similar look. Its a great bike as my daily driver
Could you hook it up with a link on where to get 2k engine paint online? Got a bud who is trying to get a similar look. Its a great bike as my daily driver
He didn't say he used 2k engine paint. Eastwood is one source for 2k engine paint. Google it and you'll find it all over the place. If these Yamaha covers are getting hot enough to be concerned about the paint I think there are bigger issues that need addressing.
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.