What's going on now over at Ichiban Moto ?

http://youtu.be/pGbDOMVfgZA

Ribo said:
So on a 4 I guess you could go on and sync 3 to 2 and then 4 to 3 using this right ?
Click to expand...

xb33bsa said:
this homemade configuration is as good or better, accuracy and usage-wise as anything you can buy.no bullshit
for four carbs you could jump around doing all combos
but just doing 2 pairs won't get it
somebody here had a multi-carb lashup with tubing and some tees
but you could just use the one and keep mixing up pairs till you got it as even as possible, no matter what pair
Click to expand...

With a vacuum manometer, you do need one line per carb.
Jumping around checking pairs does not work on a 4 cyl as you need to balance the vacuum between all carbs at once with a manometer.
( this is not the same as measuring specific vacuum values as you would do with a proper set of vacuum gauges)

Here is how to make a 4 cyl. manometer ( some stovetop science ;D)

http://youtu.be/9MtdUaiBnIo
 
Re: What's going on now over at Ichiban Moto ? a Bad Ass Electrolysis kit !

I made a diy setup to safely remove rust with electrolysis , works bad ass !

here is the video ;D :

http://youtu.be/3KA7wVTW1Oo
 
Did you do this?
http://www.tickld.com/x/the-best-craiglist-ad-ever-this-man
a_533_20140531215831.jpg
 
on the 4 port manometer, do the lines need to be equal length to the "T" ? The curve of the outside lines would make them longer than the ones going into the T, yeah?
Would it be easier to ensure equal length if you put elbows on the outside so that the bottom is equal? for example:
II II II II
II II II II
II II II II
L___JL___JL___J


ON ANOTHER NOTE,
for the electrolysis, can you put a whole tank in a plastic storage tub and do this same thing? would the rust travel out from inside the tank and to the sacrificial piece
 
Depending on the set up, it is possible to balance a 4 by doing 2 carbs at a time but it's time consuming and a PITA
CBX 6 cyl is done as two three cylinder motors then as a two cyl to get left and right banks matched
Actual line length isn't too important, just fit 1/16" restrictors in the fixed part of tube.
Old air jets work to slow down the movement of fluid, smaller than 60 makes things go too slow though
 
Another one - you need your own daytime show on the speed channel or something dude. This is awesome!
 
Ha! Careful, X3isthemagicnumber, it's the amperage that hurts
 
Re: What's going on now over at Ichiban Moto ? ding removal

I borrowed my neighbor's paintless dent/ding fix kit to try on a motorcycle gas tank.

Here is my review video :

http://youtu.be/I4JkLX3AIjU
 
Re: What's going on now over at Ichiban Moto ? Cafe Racer Headlight Kit

I helped out a guy from another forum with his headlight kit ;D

Here is the vid:

http://youtu.be/uE2VsNgZ2O4
 
Ichiban, that is another great video, you make it look so easy but I don't know if I would want to attempt to do that myself. I don't have a measuring device and from your video it looks like the measurements are critical.
 
I'm selling those kits for $600 - for and additional $1000 you can upgrade to 250 µm tape. I have extremely reliable data that show this additional tape thickness adds over 500bhp to any motorcycle made before 1985.5.
 
You must log in or register to reply here.

DTT Light or Dark

  • DTT Light
    • www.jadusmotorcycleparts.com
    www.lostapostle.ca/
    www.sparckmoto.com

    Spread the Love

    Back
    Top Bottom