Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature currently requires accessing the site using the built-in Safari browser.
We noticed you are blocking ads. DO THE TON only works with community supporters. Most are active members of the site with small businesses. Please consider disabling your ad blocking tool and checking out the businesses that help keep our site up and free.
Almost like new, only had them on for a few rides but ended up deciding to keep the stock stem mirror. These are $95 +s/h new from DCC. Asking $60 shipped.
https://www.ebay.com/itm/3-Brushed-Aluminum-7-8-Cafe-Racer-Bar-End-Mirrors-from-Dime-City-Cycles/264321774205
More Info on DCC...
Wondering if anyone knows of a good solution to running both passenger pegs and rear sets. I’m working on a 71 cl350 and was considering replacing the bolts at the the bottom of the rear shocks with footpegs. If they’re the same thread pitch I can’t think of why it wouldn’t work.
The R/R appears to be functioning normally. The battery measured around 13.3V and climbed no higher than 14.2V revving. I suppose the next step is to test the voltage across the 35W headlight.
The wiring run goes from the battery to the keyed ignition, to a 14ga bus into a 16ga wire at the RH control cluster, which leads to the LO/HI switch on the LH control cluster, and then to the headlight. All is 16ga except for the 14ga + bus.
I haven't checked the output of the alternator yet...
So I'm riding in Bellingham, WA late last night. I turned onto a country road going about 45mph and switched on my High Beam. Not 10 seconds later it's suddenly totally dark. My headlight went out. Thankfully I was on a straightaway. I pull the clutch and shift down, pull to the side of the road...
Bought 17" reverse cone mufflers to fit on a 71 CB350. Header OD is 1 1/2" muffler ID is 1 3/4. I used the reducers that came with the mufflers and they still feel very loose when clamped down. They can wiggle quite a bit and don't take much force to slide off. I stacked two of the reducers...
I've read the 101 and FAQ threads, but I'm still a bit confused over how to wire the main + and ground wire that most of the bike's components will connect to.
In a stock cb350, the fuse between the battery and ignition switch is rated to 15A and connected to a 16ga wire. Max current for a 16ga...
Can't find connectors like this anywhere in town, anyone know where I could find them online? Look like maybe 2 into 2 open barrel butt connectors. I like them because they're so compact, trying to use as many crimped connections over soldered as I can.
Sent from my iPhone using Tapatalk
I've read that you should run the bike after wrapping the pipes to cure the wrap, making it smoke a little. Does this need to be done right after wrapping when the wrap is still wet?
The bike isn't running yet but I wanted to have them ready. Will it still be good to cure in a month when the...
How critical is the length of a wiring run? How much does the resistance of wiring come into play in this application?
I'm making a harness from scratch and I plan on only giving enough length to meet my components and a few extra inches on some runs to make changes later on if necessary.
My...
When doing a compression test, would running non-stock carbs, air filters, or mufflers affect the overall compression value? Could a test be run without all of the above and give accurate results?
Sent from my iPhone using Tapatalk
These lithium batteries are evolving so fast, it seems the ones available now are much stronger than batteries from even a few years ago. Anyone used a lithium ion battery that's served them well they could recommend?
I've heard that lithium batteries smaller than stock aren't reliable for...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.