Search results

Hi All, Tried lots of searches but struggling to find exactly what I am after. I am building a Cb360 (and also have some spare Cj360 engine/parts knocking about). I am going to weld up the exhaust myself (a 2-1) but can't find what the stock pipe diameter is for the CB360, does anyone know...

That doesn't sound like too bad a price at all, a lot more reasonable than I was expecting. I'll get in touch with pbi and see what it'd be to get one shipped to the UK. Cheers

Thanks J-Rod, Was hoping to avoid custom parts but if i can't find anything else will take a look. Cheers,

Hi all, I am building a cb360 cafe racer here in the UK. I am using a Yamaha SR rear wheel and the smallest rear sprocket size I can get is 38 so I would like to go up to 18 front to get close to standard ratios. I can find these parts for the standard 530 chain but struggling to find a front...

Cheers for the replies guys! Will use the best cam and rockers out of the 3 then. Will look at the tensioners as well and make sure they are the updated kind before fitting. Thanks for the link plagrone, very helpful! Hopefully get the engine build complete this weekend!

Hi All, Currently rebuilding a CB360 engine, but also got a couple CJ360 engines sat around that came with the bike when i bought it. Currently at the top end and had a couple of questions. Are the cam shafts the same between the 2 bikes? One of the CJs shafts are in better condition than the...

Yeah i was worried that would be the case, i would try repair my one if i hadnt mislaid it! never mind, will scour ebay! Cheers

hi all, I have been stripping down my controls and switches on my cb360. The knob for the kill switch was broken when i got it and need to find a replacement. Does anyone know where I might be able to get hold of one? Cheers

The liners never came out completely, and they werent near any dirt when they were loose so shouldnt have got anything in them. They were at about 110/120 Degree C for around an hour

Hi Guys, I have been rebuilding my CB360 engine, and as part of that I have painted it all up. I have painted it using the VHT engine enamel, and have just baked it as recommended. As i took them out I noticed the liners were completely loose (I guess the ally case expands more than the steel...

I was more looking for something I could buy second hand off an older bike. Also needs the brake mounts as part of the unit. Thanks though neevo, they do look like great parts and look like something I could use on a future build!

Hi Guys, Looking for a bit of inspiration regarding handlbar controls and levers etc. I'm building a CB360 cafe racer style bike, and have got clip-ons. I am trying to find a nice clean solution for throttle cable, brake levers and electrical controls all in one package. It will also need to...

Thanks myd, will take a look through you build. not sure Ill go as far as adding an external cooler, but always good to go through some inspirational threads

http://www.bikebandit.com/houseofmotorcycles/1980-yamaha-sr500g/o/m7626#sch219677 Looks pretty close to me! I don't have the wheel at the minute, its off getting blasting so can't check the number, none of the photos I have show all the number. Will confirm with the number when i get it back...

Hi guys, I brought a project bike a while a go which came with a set of yamaha wheels. I was told the wheel were off an XS of some kind. Hvaing looked around, i believe the front wheel is from an XS400 so no problem there. I assumed then that the rear would be from a xs400 as well, but having...

Thanks Myd, only just seen this reply. I dont plan on revving the crap out of the bike everywhere I go, but just dont want to be afraid of winding it open on occasion. Opening up that piece I think I will definetly do. Looked at Crazypjs thread on the matter and looks fairly straight forward...

Trek, some brilliant threads there. Will get reading through them! Cheers

Hi Guys, I realise I might annoy people by asking this, as I imagine it has been covered many times before. I am rebuilding a CB360 engine and I just want to make sure I get it right and don't miss anything. I have searched through the forum and general google search and have found a few things...

cheers for the responses guys, had the forks apart and the bolt in the bottom of the stanchion is the same, so it should work. I quite like the yam wheels so would like to use that. cheers anyway though mrlvlagic

Hi All, i recently bought a CJ360 with a big box of spare parts. It came with a set of XS400 wheels, and front forks. as well as the original front end of the CJ. I want to use the XS front end (like the look of the wheel, and disc rather than drum), and it slides right in to the CJ triple...