1972 CB175. first bike, first build.

my turn signals finally showed up today. and...








they work!

i was worried that my switch was toast after all the problems i was having with the mini LED signals i had before. it was actually just not enough load or too much load or whatever for the LED flasher to figure out. im glad i have signals now, since 95% of drivers in florida should never have a licence in the first place. at least if i get hit they cant say i dont have signals.
signalsfrontshot.jpg

.
signalsrearshot.jpg

.
signalssideshot.jpg
 
the build looks great. all the wiring stuff sounds like what i'm going to be having fun with this week i'm just waiting on grips and a brake and clutch handle. where did you get the new clutch/brake cable? i'm wondering if i should get a new one. keep up the work
 
chris73cb175 said:
the build looks great. all the wiring stuff sounds like what i'm going to be having fun with this week i'm just waiting on grips and a brake and clutch handle. where did you get the new clutch/brake cable? i'm wondering if i should get a new one. keep up the work
the front brake cable is og and the clutch cable i bought nos from ebay. my old clutch cable was so bad that i have a permanent red spots/blood deposits under my skin across my middle 3 fingers. cables are a good thing to replace anyways, so might as well do em all.
 
no real updates with the bike besides putting in bigger main jets and enjoying it everyday.
lot1.jpg

.
lot2.jpg

.
lot4.jpg

.
lot5.jpg
 
need some help here! ive been having troubles with the bike running like shit lately. once the bike gets hot (usually on longer rides, 10 miles or more i would guess) it starts to run on 1 cylinder and will sputter and back fire out of the non running cylinder and will only keep running if i have the throttle wide open. if i let off the bike just shuts completely off. im going to take the petcock off tomorrow and try to clean it as well as shorten the fuel lines because one rests on the tappet cover and i thought perhaps the heat from the head was causing the gas to boil. im stumped... anyone know what it may be?
 
Has this happened more than once the same way? In other words, if you let the bike cool down it then starts and runs fine again and then the symptoms repeat? I don't really have any idea but I had a bike with a bad coil do weird stuff sort of like that once.
 
Im with Diesel on this one. Next time it shuts down, let it sit for about 20 minutes and try to fire it back up. If it runs fine, it's your coil.

Matter of fact, i have an old coil you can have. Not a Dyna, but it works good.
 
thats exactly what happens. ill be cruising along, itll start sputtering, run on one cylinder, and then eventually just shut off and not start. so i have to pull over, shut the bike off and sit for 10 minutes and then the bike starts right up and is good for another 2-3 miles before it all happens again. you think its the coil? rich if your willing to send that coil my way, whats your paypal, ill pay for shipping and supplys to get it here. this problem is getting so god damn annoying. it happened to me again last night on my 2 mile or so ride from the bar home. >:(
 
Pm me your address and i should be able to get it out asap. I'll get home later today and double check that it's usable.
 
IS there a way to lift the rear of the tank an inch or so. It would really make the lines flow a lot better.
 
Andrew,

Are you sure it's not a blocked breather hole in the filler cap? There is a tiny (<1/16") hole that air goes in to replace the fuel as it runs and they rust and get clogged.
 
teazer said:
Andrew,

Are you sure it's not a blocked breather hole in the filler cap? There is a tiny (<1/16") hole that air goes in to replace the fuel as it runs and they rust and get clogged.

yeah it could be. i take it by filler cap you mean the gas cap? the gas cap is og and pretty nasty on the inside so i imagine it could be that. thanks for the heads up.
 
well i may have figured out why it was cutting out or running funny. the pos. blue wire coming from the points was soldered togeather at some point in its life and was a pretty bad solder job.
photo.jpg

i cut it out and used a butt connector to put the wires togeather and it seems to run fine now but i havnt taken it on a long ride yet to get the temp. up.


now my question for those of you who have swapped out coils. did you guys just cut the 2 wires that are connected to the ends of the coil and crimp on a spade connector for the new coil's + and - leads? (the black wire on the end without the plug wires and the blue wire on the end with the plug wires going into it)
pictures of what im talking about.
gfhgf.jpg

.
fhfhf.jpg

sorry for the noob question, i just wana get this right the first time when i order the new coil.
 
Fantastic bike, it looks amazing! I will follow with great interest.

I am curious to see the outcome of your coils/points change, as my cb360 is having similar issues and its possible its the same problem.
 
ordered these little guys last night. hopefully it will remedy my missfiring and shutting down issues. *crosses fingers*
20gjp5u.jpg

.
Picture2-1.png
 
Those things should help you a lot! You won't have to do any cutting and crimping everything just pops out and pops in. the wires on your new coil will go to the matching wires in the harness.

I've got one question for the group watching here; how do you know which spark lead goes to which cylinder with these things? I didn't even think about it when I replaced mine, just put one on one and the other on the other. Did I just get lucky or doesn't it matter? seems like it would matter.
 
Yeah, curiosity got the best of me and I went out and switched em around. no diff and now my "NGK" logos are right side up!! ;D
 
Back
Top Bottom